Old Well Remediation in the Piedmont Triad

Old wells fail in familiar ways. Steel casing rusts through, the wellhead ends up below the grass, and the water turns orange or keeps testing positive for bacteria.

We seal off rusted-out casing with a liner, bring the well up to code, and work to get the water back to clean drinking water.

How an old well shows its age

Most of the old wells we see were drilled decades ago and have not been touched since, apart from a pump or two. They rarely fail all at once. They wear out at the top first, where the casing meets damp soil and air, and the water is usually the first thing to change.

  • Rust at the ground line, or a casing that moves when you push on it.
  • Orange or brown water, rust flakes in the toilet tank, or a metallic taste that keeps getting stronger.
  • Water that turns cloudy a day or two after a hard rain.
  • Bacteria tests that keep coming back positive, even after the well has been chlorinated.
  • Grit in the filters, the faucet screens, or the bottom of the pressure tank.
  • A wellhead buried in a flower bed, sitting in a pit, or capped with a lid that just rests on the pipe.

Any one of these can have a simple cause. Two or three together usually mean the well itself needs work, not just the equipment hanging in it.

Sealing rusted-out casing with a liner

When steel casing has rusted through, patching the outside rarely holds. The lasting repair is a liner: a smaller pipe set down inside the old casing, with the gap between the two filled with cement grout. The damaged steel stays in the ground, but your water no longer touches it.

North Carolina's well construction rules allow NSF-approved PVC rated at 160 psi as liner pipe, and they call for the space around it to be completely filled with cement grout. That grout is what turns a pipe inside a pipe into a seal.

Liner work means the pump comes out first. We measure the old casing and the pump before anything goes down the hole, because a liner narrows the inside of the well. If the pump and its fittings pass through, the pump can go back in. If they do not, the plan includes a slimmer pump, and you hear that before we start. With everything out of the hole anyway, it is also the right time to look over the drop pipe, the wire, and the splice.

A liner can help in one more way. In some older wells, soft rock just below the bottom of the old casing keeps crumbling and sending grit to the pump. Lining down through that stretch stops it from feeding sand to the pump, the tank, and the faucets.

Bringing an old well up to code

Plenty of wells were legal the day they were built and fall short of today's rules. Bringing one up to code is mostly about the wellhead, the few feet where surface water and the well meet.

  • Casing height. North Carolina and Virginia both want the casing to end at least 12 inches above the ground. North Carolina also says a well may not be repaired in a way that leaves the wellhead lower than that.
  • Grading. The ground right around the casing should fall away from the well, so rain runs off instead of pooling against the pipe.
  • The cap. A sanitary cap fits snug on the casing, is bolted in place, and breathes through a screened vent.
  • Pit wells. A wellhead sitting in a pit collects runoff right where the casing ends. The usual fix is extending the casing up out of the pit, fitting a sanitary cap, and regrading.

Paperwork comes with it. In North Carolina, repairing a private well takes a permit from the county health department, and a certified well contractor has to be present for the repair, any casing extension, and the disinfection. In Virginia, a written permit has been required since November 6, 2024 to alter a private well, though swapping a cap for an equivalent one or extending the casing above ground does not count as an alteration. We hold North Carolina water well contractor certification 2453-A and Virginia water well license 2719001436.

North Carolina's rules are firm on one point: broken or defective casing, seals, or wellhead parts have to be repaired or replaced, or the well has to be permanently abandoned. Fixing an old well while repair is still an option keeps that choice yours.

Getting the water back to clean drinking water

Sealing the well stops new contamination from getting in. The next step deals with what is already there.

Every job that opens the well ends with shock chlorination. Under North Carolina's rules, that means a strong dose, 100 parts per million, held in the well for 24 hours or more, and nobody uses the water until pumping shows the chlorine is gone. Virginia requires disinfection after work inside the casing as well. On an old well, the first water pumped out can run rust-colored and full of sediment before it starts to clear. Our gallery page has two short videos of an old well being flushed, an hour apart.

Then the water goes to a certified lab. NC DHHS says to test after any part of a well is repaired or replaced, and a bacteria test is the one that tells you whether the sealing worked. Some problems are not the well's fault. Iron, manganese, and hardness can come straight from Piedmont rock, and sealing the casing will not change them. If the lab results show that, we size a water treatment system to the numbers on the report, not to a guess.

Fixing the old well before thinking about a new one

We do not drill new wells, so we have no stake in talking you into one. Here is the plain case for remediation first. Your old well already has a hole in the rock that produces water, a line to the house, and wiring in place. A new well means a health department permit, a location on the lot that clears the required setbacks, a rig in the yard, a new trench, and a new pump, and the new hole still has to find water in the same rock.

Remediation keeps the parts that work and fixes the parts that do not. When a casing is too far gone to save, or the well cannot be brought up to code, we will say so, and North Carolina's rules then point to abandoning it properly.

How a remediation job goes

  1. Look and listen. We start at the wellhead with a tape measure and a flashlight, and ask what the water has been doing and whether you have any recent lab results.
  2. Test the water. If there is no recent result, a sample goes to the lab, so there is a starting point to compare against.
  3. Pull and inspect. With the pump out, we can see the casing from the inside and measure it for a liner.
  4. Lay out the plan. You get the options in plain terms: a liner, a casing extension, a new cap and regrading, a slimmer pump if one is needed, or some mix of those.
  5. Permit, then work. Any permit the county or health district requires comes first.
  6. Disinfect and flush. Chlorine goes in, sits, and gets pumped out until it is gone.
  7. Retest. A lab test after the work shows where the water stands now.

The water is off while the pump is out and the liner goes in, and again while the chlorine sits in the well. Fill a few jugs and the bathtub before the work starts. You will know ahead of time how long the house should be without water, and the lab result tells you when the water is ready to drink again.

Call (336) 613-4314 and tell us how old the well is, what the water has been doing, and where the wellhead sits. For technical questions, our office manager gets the right person on the phone.

What is down there, and what can go wrong

Tap a part, or pick one from the numbered list, to see what it does. Press "Run the pump" to watch the water move.

How a private well system works Cutaway of a drilled well: cap and casing above the ground, a pitless adapter below the frost line, a submersible pump hanging in water-bearing bedrock, and a buried line to the house where the pressure tank, pressure switch, control box and treatment sit. TOPSOIL RED CLAY AND WEATHERED ROCK BEDROCK frost line water level
  1. A sealed, vented cap keeps out rain, insects and small animals. A cracked or loose cap is one of the easiest ways for bacteria to get into a well.

    Well Repair, Casing Repair and Well Liners
  2. Pipe that lines the top of the well and seals it from surface water and loose soil. It should stand above the ground, never be buried.

    Well Repair, Casing Repair and Well Liners
  3. The fitting on the side of the casing, below the frost line, where the water line leaves the well for the house.

    Well Pump Troubleshooting and Repair
  4. Sits down in the water and pushes it up to the house. Most drilled wells use one. Shallow wells and some older systems use a jet pump above ground instead.

    Well Pump Installation and Replacement
  5. Carries water up and power down. A split pipe or a bad splice can look exactly like a dead pump.

    Well Pump Troubleshooting and Repair
  6. In the Piedmont, wells draw water from cracks in the bedrock. Hydrofracturing can open more of them in a well that gives too little.

    Well Rehabilitation and Hydrofracturing
  7. Holds water under air pressure so the pump does not start every time you open a tap. A tank that has lost its air makes the pump short cycle.

    Pressure Tank Installation, Replacement and Tuning
  8. Turns the pump on at the low setting and off at the high one. Pitted contacts or a clogged sensing tube stop the whole system.

    Pressure Switch, Control Box and Wiring Repair
  9. Three-wire pumps have a control box on the wall with the start parts. Two-wire pumps do not.

    Pressure Switch, Control Box and Wiring Repair
  10. Filters, softeners and disinfection go after the tank. A lab test tells you which one, if any, you need.

    Well Water Treatment Systems

Old Well Remediation: common questions

Still stuck? (336) 613-4314

What does old well remediation include?

Three things, usually together: sealing off rusted-out casing with a liner, fixing whatever keeps the well from meeting today's rules at the wellhead, and getting the water back to clean drinking water, checked by a lab test after the work.

Do I need a permit to line or repair my old well?

In North Carolina, repairing a private well takes a permit from the county health department, while pump and tank work does not. In Virginia, altering a well has needed a written permit since November 6, 2024, though a cap swap or a casing extension above ground is not an alteration. We tell you which applies before any work starts.

Will a liner change how much water I get?

The water still comes from the same rock. What a liner changes is the inside of the well, which gets narrower. That is why we measure the casing and the pump first. If the pump fits through the liner it goes back in, and if it does not, a slimmer pump is part of the plan from the start.

How can I tell if my old well is out of code?

A few things you can check from the yard: the casing should stand at least 12 inches above the ground, the cap should be bolted down with a screened vent, the ground should slope away from the pipe, and the wellhead should not sit in a pit. The grout seal and the condition of the casing below ground take a closer look.

My well sits in a pit below the ground. Can it be fixed?

Usually, yes. The common fix is extending the casing up and out of the pit to at least 12 inches above the surrounding ground, fitting a sanitary cap, and grading so water drains away from the wellhead instead of into the pit.

How long before we can drink the water again?

The chlorine has to sit in the well for at least 24 hours under North Carolina's rules, and then the well is pumped until no chlorine is left. After that, a lab test shows whether the water is clean. Plan on bottled water for drinking until that result is back.

Will this fix orange, rusty water?

It depends on where the rust comes from. If corroded steel casing is the source, sealing it off with a liner removes that source. Iron that comes naturally from the rock stays in the water no matter how good the casing is, and a treatment system handles that. A lab test tells the two apart.

Should I fix my old well or drill a new one?

We do not drill, so here is the straight answer: if the well still produces water and the casing can be sealed, remediation keeps the hole, the line to the house, and the wiring you already have. If the casing is too far gone or the well cannot be brought up to code, a new well and proper abandonment of the old one become the path, and we will tell you that plainly.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.