Well Pump Replacement in Burlington, NC

Nobody wants to replace a pump that only needed a switch, or keep patching one that is finished.

Map: Burlington, NC in relation to GreensboroBurlingtonGreensboro19.8 miElonGibsonvilleGrahamALAMANCE
Town
Burlington, NC
County
Alamance County
From our Greensboro office
19.8 miles, straight line
Open Burlington in Google Maps

The well pump replacement Burlington homeowners get from us starts with testing, not a guess. When the motor has burned out or the pump is worn past saving, in a house from the textile years or a new one, a new pump is the honest fix.

What a well pump replacement in Burlington involves

Submersible pumps

Down in a drilled well, a submersible pump hangs on its drop pipe with the motor below the pump end. Replacing one means breaking the well seal, lifting out the pipe, wire, and pump together, and lowering a new assembly back to the right setting. The new pump has to fit both the well and the house: enough output for how your family uses water, but not so much that it outruns what the well can give.

Jet pumps

A jet pump sits above ground, usually near the pressure tank. Nothing comes out of the well, but the new pump still has to be primed, matched to the water level, and set up for the right pressure range.

Parts worth changing at the same time

With the old pump out, we study what came up with it. Brittle drop pipe, nicked wire, a tired check valve, and corroded splices are far easier to deal with now than after the new pump is back down the hole. The switch and tank get a look too, because a new pump working against a waterlogged tank will not last.

Why a dying pump should not be left to run

Worn pumps do not fail politely. Output drops a little at a time, so the house slowly loses pressure while the motor runs longer to keep up. Longer runs mean more heat. Eventually the windings break down or the thermal overload trips again and again, and one morning the pump does not restart.

The trouble rarely stays inside the pump. If sand is what wore it down, that same sand is moving into your lines and settling in the pressure tank. A motor drawing too much current can overheat the wire in the well or burn out the control box. And a pump that finally quits during a cold snap or a dry spell leaves the household with no water until the replacement is in.

Clues that repair is no longer enough

The motor tests bad. Shorted windings or insulation that reads grounded means the motor is finished. Submersible motors are not rebuilt in the yard.

Pressure keeps fading with a good tank and switch. A pump with worn impellers still runs, but it can no longer build pressure the way it did.

Sand or grit shows up at the taps. It can mean the pump hangs too close to the bottom or the well is shedding sediment, and the new pump should be set with that in mind.

The breaker trips the instant the pump starts. Once the switch, the surface wiring, and the control box check out, a locked or shorted motor is the likely answer.

The pump never fit the job. An older house may still run a pump chosen for a smaller household, or a jet pump straining against a water level it was never meant for. If yours has always struggled, the right size fixes the cause instead of the symptom.

Replacement day, from the first test to running water

First we confirm the diagnosis. Even if someone else has called the pump dead, we test the motor and wiring ourselves, because a bad control box or a broken wire can look the same.

Next comes the pull. On a submersible, that means removing the well cap, releasing the pitless adapter, and lifting the whole string out of the casing. We lay it out and read it: how far down it hung, the shape of the pipe and wire, any scale or sand on the pump, and what the old motor's nameplate says.

Then the new pump goes together with fresh splices, a check valve, and a torque arrestor where it belongs, and we lower it carefully so the wire does not rub against the casing on the way down.

Once it is wired and running, we watch pressure build and check the switch settings and tank charge. The well gets disinfected before it goes back into use, and we recommend a water test once the chlorine has cleared, since NC DHHS advises testing after any well component is replaced.

Railroad roots, newer builds, and the wells in between

The North Carolina Railroad put repair shops here around 1851. The community was known as Company Shops until 1887 and was incorporated in 1893, three years before the shops moved to Spencer in 1896. Textiles carried the city after that. Burlington Industries, founded in 1923 by J. Spencer Love, dominated the industry for much of the twentieth century.

A place with that much history does not have one kind of house, or one kind of well. An older home may sit on a well that went in long before today's rules, with a jet pump in a crawlspace or a submersible that replaced something older. Records for those wells can be thin, so we learn the well by pulling the pump and measuring what we find. Newer homes are more likely to have a drilled well with a submersible and a construction record that tells us depth and casing before we lift anything.

New building runs under two sets of rules. Inside the city, the Unified Development Ordinance governs all new development. Out in the county, Alamance County updated its Land Development Plan in November 2020 to guide land use decisions. Those rules shape where houses go; the pump in each well still has to suit that one well.

Lining up a replacement from Greensboro

We are a small independent company in Greensboro, and Burlington is regular territory for us. US 70 is one of the roads that brings us over. We hold North Carolina water well contractor certification 2453-A, and state rules require a certified well contractor whenever the well seal is broken for pump work.

Office hours are 8am to 5pm on weekdays. Weekends, text or call. Either way the number is (336) 613-4314, and we will set a time once we know whether the pump has failed outright.

ZIP codes we cover around Burlington: 27215, 27217.

Questions from Burlington

Still stuck? (336) 613-4314

Part of Burlington is in Guilford County. Does that change anything for my well?

For the pump work itself, no. The Census Bureau estimates that about 2,633 of the city's residents live in the Guilford County part. If the house is on that side, Guilford County's health department, not Alamance County's, handles any well permits and county sampling. The state's rule on disinfecting a well after pump work is the same on both sides of the line.

Do you also replace pumps in Elon, Graham, and the other towns near Burlington?

Yes. Along with Burlington, we work in Elon, Gibsonville, Graham, Whitsett, and McLeansville, so a well a few miles over is still in our area. Call the same number, tell us the street address and what the pump is doing, and we will sort out the visit from there.

We are building outside Burlington. Can you put the pump in our new well?

We do not drill wells, so the hole itself comes from a well driller, and the county health department issues the well permit. Inside the city limits, new development also falls under the Unified Development Ordinance. Once the well is finished, we can help with the pump, tank, and controls, sized to that well and to your household.

Will a new pump fix low pressure in my house?

Only if the old pump is the reason. Low pressure can come from a waterlogged tank, a clogged filter, a switch set too low, a leak in the buried line, or a well that cannot keep up. We test before recommending a new pump, because a bigger pump on a tired well can make things worse by pulling the water level down faster.

Does the well have to be disinfected after a pump replacement?

Yes. North Carolina rules require disinfection after a pump is installed or repaired. The chlorine has to reach at least 100 parts per million in the well and stand for 24 hours or more, then the well is pumped until no chlorine shows. After that, testing the water is a good idea, since anything can slip in while a well is open.

Should I go with a submersible or a jet pump?

It depends on the well. Most Piedmont wells are drilled into bedrock, and a submersible is the usual choice for those. A jet pump can make sense on some shallow wells, or where the existing setup is built around one. We look at the water level, how the well was built, and where the equipment can sit before suggesting either.

Can my old drop pipe and wire be reused with the new pump?

Sometimes. If the pipe is sound, the wire insulation tests clean, and the splices are in good shape, reusing them is reasonable. Old pipe that has gone brittle, or wire with nicks along its length, is a different story. A new pump hung on failing pipe can break loose and drop down the well, and getting it back out is slow, difficult work.

How do I know my pump is truly dead and not just tripped?

If the breaker is on and the pump makes no sound, the problem could be the switch, the control box, a broken wire, or the motor. If it hums but delivers nothing, the pump may be locked up or the pipe may have separated. Do not keep resetting breakers or open any electrical boxes. Call, and we will test it.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.