The culprit is hydrogen sulfide, and it can come from the groundwater, from bacteria living in the well or the lines, or from equipment inside the house. Before you spend anything on a filter, find out which one you have. A lab test settles it.
Three places a sulfur smell can start
Hydrogen sulfide is what gives water that rotten egg smell. It gets into your water in one of three ways.
- In the groundwater itself. Some groundwater carries dissolved sulfide picked up underground, especially where oxygen is scarce. USGS notes that iron, manganese, and sulfate locally occur at objectionable levels in Piedmont groundwater.
- From bacteria in the system. Sulfur-reducing bacteria feed on sulfate and give off hydrogen sulfide. They can live in the well, in the pressure tank, or in a filter or softener that has gone too long without service.
- On the hot side of the house. If the smell only shows up in hot water, the source is usually the hot-water equipment, not the well. That is a job for the trade that services that equipment.
The fix is different for each one, which is why equipment bought on a guess so often misses.
A five-minute sniff test at your taps
Fill a glass at each of these spots and smell it right away.
- Cold water in the kitchen. This is your baseline.
- Hot water at the same tap. Compare the two.
- The hose connection at the pressure tank. On most systems it comes off the line before any treatment equipment, so it is the closest you can get to raw well water.
Then read the pattern.
- Smell in hot water only: look at the hot side of the house first.
- Smell everywhere, including at the tank: it is coming from the well or the groundwater.
- Smell on treated taps but not at the tank: the treatment equipment is the likely source.
- Strong at first, then fading after the water runs a few minutes: often bacteria in the well or lines.
- Steady no matter how long it runs: more often sulfide in the groundwater.
Test the water before you buy a filter
Treatment chosen by nose alone often treats the wrong problem. A carbon filter bought for a bacteria problem can turn into a new home for the bacteria.
A useful test for a sulfur smell covers:
- Total coliform and E. coli, since a smell tells you nothing about bacteria and only a lab can find them
- Hydrogen sulfide
- Sulfate
- Iron and manganese, which can travel with sulfur problems and change what treatment works
- pH
Hydrogen sulfide escapes from water quickly, so collect and handle the sample exactly the way the lab says, often in a special bottle. NC State Extension recommends testing for sulfate, iron, manganese, and a few others every three years anyway, so this is a good time to catch up. We can go over the results in plain language and tell you what each number means for your house.
Matching the fix to what the lab finds
Bacteria in the well or tank
Shock chlorination kills them, at least for a while. Virginia Cooperative Extension recommends it after a positive total coliform test and warns that bacteria will keep returning if a source such as a loose well cap or cracked casing is not fixed. Find the way in and close it, then disinfect and retest.
Light sulfide in the groundwater
Activated carbon can handle a faint odor. It fills up, though, and needs fresh media on schedule, or it stops working and can start to smell on its own.
Heavier sulfide, or sulfide with iron and manganese
These usually call for a system that oxidizes the sulfide, using air or a chlorine or peroxide feed, and then filters out what it knocks loose. Sizing depends on the lab numbers and how much water the house uses.
The treatment equipment itself
A softener or filter that has gone years without service can grow the very smell it was bought to remove. Sometimes it needs cleaning and fresh media, and sometimes it needs replacing. A softener alone does not remove hydrogen sulfide.
When the smell shows up out of nowhere
Water that was fine for years and suddenly smells is telling you something changed. EPA recommends testing right away when you notice a change in taste, color, or odor. Common triggers are a cracked or loose cap letting runoff in after heavy rain, recent work that opened the well, and a long dry spell that can change how water moves into the well.
NC DHHS also recommends testing after any repair or replacement of a well part. If the smell started right after a pump or tank job, say so when you call (336) 613-4314, because it narrows things down.