Well owner tips, November 13, 2026

No Water After a Power Outage? What to Check First

The storm passes, the lights come back on, and the kitchen tap gives you a sputter of air and nothing else. Most well systems restart on their own once power returns.

When yours does not, the cause is often simple, and a few safe checks will tell you whether to wait or pick up the phone.

Why the water goes when the power does

Your well pump runs on electricity, so when the power drops, the pump stops. The pressure tank holds a little water under pressure, enough for a few minutes of normal use, and then the taps go dry.

When power returns, the pressure switch sees low pressure and starts the pump. The tank refills, the switch shuts the pump off at its set pressure, and you never notice. If that does not happen, one link in the chain did not come back: the breaker, the pressure switch, the control box, or the pump itself.

Safe checks at the breaker panel and the tank gauge

These are safe for any homeowner.

  1. Make sure the whole house has power. After some storms, power comes back on only part of the house. Lights work, but larger 240-volt loads, often including the well pump, stay dead. If some rooms are dark or lights look dim, call the power company first.
  2. Find the pump breaker. It is usually a two-pole breaker marked "well" or "pump." If it tripped, push it fully off, then back on, one time. A second trip is your signal to stop and leave the handle down.
  3. Look for a second switch. Some homes have a separate disconnect or a plain wall switch near the tank. Make sure nobody bumped it while hunting for flashlights.
  4. Read the tank gauge. Zero or close to it, with power on, means the pump is not delivering water. A normal reading with dry taps points to a problem past the tank.
  5. Listen. You should hear the switch click and, with a jet pump, the motor hum. Silence tells us something. So does a hum with no water.

Do not open the pressure switch or the control box, and do not tap the switch with a screwdriver handle to get it going. That old trick puts your hand next to live terminals. Some switches also have a low-pressure shutoff that has to be reset by hand after pressure falls too far. It sits right beside those same terminals, so leave it to us.

When lightning or a surge did the damage

Lightning and power surges are a common reason a pump or control box quits. A strike does not have to hit the house. It can come in on the power line or through the ground and find the pump down in the well.

On a three-wire submersible, the control box on the wall holds the starting parts, and those often take the hit. That is the better outcome, since the pump stays in the well. A two-wire pump has no control box. Its starting parts are inside the motor, so a surge that gets through goes straight to the pump. The pressure switch can suffer too, with contacts that burn or weld and leave the pump stuck off or stuck on.

A good well tech tests the switch and control box with a meter before anyone talks about pulling a pump. Once the repair is done, ask about surge protection for the pump circuit.

Jet pumps that come back without their prime

A jet pump sits above ground and pulls water up to itself, so it has to stay full of water to work. During a long outage, a leaky check valve or foot valve can let that water slip back down the line. When power returns, the pump runs and hums but moves nothing. That is a lost prime.

Turn the pump off at the breaker if it is running without moving water, because a jet pump running dry heats up and cooks its seal. Priming it again is often simple. A pump that loses prime after every outage, though, has a valve or suction leak that needs fixing.

If floodwater reached the wellhead

If the wellhead or the well house sat under water, leave the pump's power off. NC DHHS says not to turn the pump's electricity back on until floodwaters recede, and it strongly recommends having a flooded well shock chlorinated by the local health department or a licensed well driller. Wet electrical parts need a check before they are energized, and NC DHHS also recommends testing the water after flooding. Drink bottled water until a lab says the well water is clear.

If the pump has to be replaced, North Carolina rules require the well to be disinfected afterward, with chlorine held in the well for at least 24 hours and then pumped out until none is detected. Expect a day of water you should not drink. Call (336) 613-4314 and we can walk through it.

Quick answers

Still stuck? (336) 613-4314

How much water is left in the pressure tank when the power goes out?

Less than most people expect. Much of a pressure tank is air, so only a few gallons are usable before the pressure is gone. Before a big storm, fill some jugs for drinking and a bucket or two for washing. It makes a long outage much easier.

Should I turn the pump breaker off during a thunderstorm?

Some owners do. Switching it off while a bad storm is overhead removes one path a surge can take to the pump. It will not stop every surge, since lightning can also reach the well through the ground, and it only helps if you remember to switch it back on.

Why is my water cloudy or brown after the pump starts back up?

Milky water that clears from the bottom of the glass up is just air in the lines. Brown or gritty water usually means the restart stirred up sediment. Run a cold tap until it clears. If it stays dirty, smells different, or the wellhead flooded, test before drinking.

Can a long outage hurt the well itself?

The well itself almost always comes through fine. Water keeps seeping in from the rock fractures while the pump sits idle. The risks are the electrical parts, a jet pump losing prime, and frozen pipes if the outage hits in winter.

The breaker trips every time the pump tries to start. What does that mean?

The breaker is protecting something: a shorted wire, a failed part in the control box, a seized pump, or a motor damaged by a surge. Resetting it over and over can make the damage worse. Leave it off, call, and tell us how quickly it trips.

Is it normal for the pump to run a long time right after power returns?

Yes, within reason. The pump has to refill an empty tank and push air out of the lines, so the first cycle runs longer than usual. If it keeps running well past that without the gauge climbing to its shutoff pressure, turn it off at the breaker and call.

Do I need to test the water after an outage?

Not after an ordinary outage where nothing got wet or opened. Test if floodwater reached the wellhead, if the pump or another part was repaired or replaced, or if the water changed color, taste, or smell. NC DHHS recommends testing after repairs and after flooding.

Can lightning damage the pump even if the house wiring seems fine?

Yes. The pump sits at the far end of a long wire, deep in the well, and a surge can reach it through the power line or the ground. Lights and outlets in the house may come through untouched while the pump, its control box, or the switch contacts do not.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.