When a house on a private well goes dry, emergency well service in Winston-Salem begins with a phone call to us and a few safe checks you can make at home, so nobody wastes time chasing the wrong problem.
What a no-water call involves
Every no-water call is a hunt for one broken link. Something between the power coming into your house and the water down in your well has stopped, and the job is finding which piece.
The list of suspects is short:
- a tripped breaker
- a pressure switch with burned contacts or a plugged sensing tube
- a control box knocked out by a surge
- a splice or buried wire that has failed
- a pump motor that has burned out
- a drop pipe that cracked or pulled loose
- a well pumped down more quickly than it can refill
Each leaves a slightly different set of clues at the panel, the switch, and the gauge. On an emergency visit we sort through them in order, fix what can be fixed before we leave, and tell you honestly when getting water back means a bigger repair.
Why a dry house cannot wait long
A house without water stops working almost at once. No drinking water, no washing, no cooking, and pets or animals still need a drink. When the pump circuit is the cause, waiting can make it worse. A motor stuck trying to start keeps heating, and flipping a tripped breaker back on over and over can burn up a motor that only needed a new relay.
Some causes bring their own risks. A pump that keeps running against a split pipe or a dry well has nothing to cool it. If a flood took the water away, turning the pump back on too early can damage it and draw contaminated water into the house. A wellhead cracked or uncapped by a storm can let surface water in until it is closed.
Reading the clues before you call
A few things you can safely look at tell us a lot.
- The breaker. If the well breaker has tripped, give it one reset. If it pops again, stop there and leave it off.
- The pressure gauge. Zero with the pump silent points to power, the switch, or the control box. Low pressure with the pump running points to the pump itself, the drop pipe, or a low well.
- The sound. A hum with no water, a click with nothing after it, and total silence each mean something different.
- The timing. Did it quit during a storm, at the end of a long dry stretch, or right after heavy use like filling a pool or watering a garden?
- The last water out. Sputtering, air, or muddy water in the final minutes is worth mentioning.
Keep the pressure switch cover and the control box closed, and leave the pump alone. Write down what you see and have it ready when you call.
How an emergency visit unfolds
Once we arrive, the order of work does not change.
- You tell us what you saw and what you already checked, so we do not repeat it.
- We test power at the panel and at the switch, and read the gauge.
- Next comes the control box on a three-wire pump, then the wire and motor are metered from the surface.
- If the electrical side checks out, we turn to the water side: the water level, the drop pipe, and the check valve.
- Whatever can be fixed with parts on the truck gets fixed. A switch, a control box part, or a splice often can be.
- If the pump or pipe has to come up, we explain why and what happens next. Any work that opens the well ends with disinfection, and NC DHHS recommends testing the water once the chlorine has cleared.
Emergency well service in Winston-Salem: the roads in and what to do first
As the crow flies, the city sits about 25.3 miles west of Greensboro. I-40 and US 421 both run through it and continue east into Guilford County, and those are the roads we take to reach you.
While you wait, a few steps help. If the breaker tripped a second time, leave it off. Save the water you have and use bottled water for drinking. Do not keep running a pump on a well you think has gone dry. Piedmont wells are mostly drilled into bedrock and draw from fractures in it, and when a well's fractures are few, heavy use can outrun them. The well needs rest to catch up. In a hard cold snap, look at whether the tank or the pipe beside it sits somewhere unheated, because a frozen line can look exactly like a dead pump.
Flooding is its own case. NC DHHS says not to turn a pump's power back on until flood waters have gone down, and it strongly recommends calling the local health department or a licensed well driller to shock chlorinate a flooded well. In Forsyth County, that means the county health department's Environmental Health staff, who handle water supply wells. We disinfect wells too, and we can talk you through the sequence.
When you call, have your street address ready, along with a nearby crossroad and what the gauge reads. That tells us which parts to load before we head your way.
Getting through to us when the taps are dry
Call (336) 613-4314 first. We drive over from Greensboro, east of the city. On weekdays from 8am to 5pm, we handle the schedule and will ask what you found. Weekends, call or text and describe what is happening. If you reach voicemail, leave the address and what the gauge reads.
Our founder has held a trade license since 1974. We are a small company, and we will not promise a time we cannot keep. What we will do is give you a straight answer about when we can come, and what to do until then.