Emergency No-Water Service in Kernersville, NC

No water at the kitchen sink, a tank gauge resting on zero, and a household that still has to cook, wash, and get out the door.

Map: Kernersville, NC in relation to GreensboroKernersvilleGreensboro16.1 miColfaxWalkertownOak RidgeHigh PointFORSYTHGUILFORD
Town
Kernersville, NC
County
Forsyth County
From our Greensboro office
16.1 miles, straight line
Open Kernersville in Google Maps

When a Kernersville well quits without warning, the cause is usually a pump, a switch, or a wire. Emergency well service in Kernersville starts with finding which one failed and getting water flowing again.

What a no-water call involves from start to finish

Every no-water call is a diagnosis with a deadline. The aim of the first visit is to find out why the water stopped and, if the parts allow it, get it running again. The cause can sit anywhere between the breaker panel and the bottom of the well.

The usual suspects, roughly in the order we rule them out:

  • A tripped breaker or a blown fuse on the pump circuit.
  • A switch whose contacts have burned, or a tube under the switch packed with sediment.
  • A dead capacitor or relay, if the pump is a three-wire unit with a control box.
  • A broken or shorted cable, most often at a splice.
  • A burst line between the wellhead and the house.
  • A frozen pipe in a well house during a hard cold snap.
  • A pump that has failed, or a well drawn down below the pump intake.

When the fault is above ground, the fix can often be made on the first trip. When the pump has to come up, you hear exactly what failed and what happens next before any work starts. Either way, you know where things stand before we leave.

What happens when a no-water problem is left alone

Some no-water problems sit still. Others get worse quickly.

A switch stuck closed keeps the pump running with nowhere for the water to go, or pumping a well that has already gone dry, and a dry motor overheats fast. A burst line keeps pushing well water into the yard, softening the soil and drawing down the well. A shorted cable trips the breaker, and each reset hits a damaged motor with another surge. A well that ran low from heavy use needs time to recover, and a pump restarted over and over before it does can cook itself. In winter, a house without water pressure can also end up with frozen lines in a crawlspace or well house, which turns one repair into two.

Then there is the household. No cooking, no showers, no water for pets or animals in the barn. The longer the wait, the more creative everyone gets with bottled water.

Telling a true emergency from a slow decline

Call right away

No water at any tap. The pump runs without stopping and the gauge will not climb. The breaker will not hold after one reset. A burning smell coming from the switch or the control box. Water pooling or bubbling up over the buried line.

Call soon, while you still have water

Pressure is low but steady. The switch clicks fast. Taps spit air now and then. These usually point to a tank or switch problem that will not last forever, and fixing it now keeps it from becoming a true no-water call.

Probably not the well

If only one tap has no water while the others run fine, the trouble is in the line to that tap, not in the well, the pump, or the tank.

What we do first at a house with no water

Order matters on an emergency, because the simplest checks often find the problem. Each step rules something in or out before we move to the next.

  1. Hear what happened: lightning nearby, the power going out, a flicker in the lights, or nothing at all.
  2. Check the breaker, then voltage at the pressure switch, then the switch itself.
  3. On a three-wire pump, check the control box's capacitor and relay.
  4. Take cable and motor readings from the surface.
  5. Walk the line from the wellhead to the house, looking for wet ground or a sinkhole.
  6. Run the pump and see whether the well is delivering water at all.
  7. Fix what failed if the part is on the truck, or lay out the next step plainly if the pump must come up.
  8. Let the pump fill the tank to cut-out and look for leaks before leaving.

Emergency well service in Kernersville: our routes and your first steps

As the crow flies, the town is about 16.1 miles west of Greensboro, and three of the roads we use most run right through it. I-40 and US 421 both bring us in from the east, and NC 150 crosses town as well. All three continue on into Guilford County. NC 66 heads north from town toward Walkertown, where we also answer no-water calls.

Before we arrive

  • Look at the pump breaker. If it has tripped, flip it back on one time. Should it trip again, leave it off.
  • If the pump runs and the gauge will not rise, switch the pump breaker off so the motor does not run dry.
  • Note what the tank gauge reads.
  • Look over the yard along the buried line for wet or sunken spots.
  • Leave the pressure switch, the control box, and the well cap closed.
  • Clear a path to the wellhead and the tank, and bring pets inside.

When a creek comes up

The town's plan notes that local creeks run through valleys with hills and plains around them, which brings flood risk to the land beside them, and Abbotts Creek runs right through town. If floodwater has covered your wellhead, NC DHHS says to keep the pump's power off until the water goes down, and it strongly recommends having the well shock chlorinated by the local health department or a licensed well driller. Have the water tested before anyone drinks it again.

Reaching us when the taps are dry

When the taps are dry, call (336) 613-4314. We pick up between 8am and 5pm, Monday to Friday, and get the visit lined up. On Saturday and Sunday, call or text. A message with your address, how the water is acting, and whether the breaker has tripped tells us a lot before we head out.

If you can, mention anything that changed recently, such as new landscaping over the water line, a utility crew working on the road, or a storm the night before. Well owners in Colfax can reach us the same way.

ZIP code we cover around Kernersville: 27284.

Questions from Kernersville

Still stuck? (336) 613-4314

How far is Kernersville from your Greensboro base?

About 16.1 miles west, measured in a straight line. Kernersville is one of the towns named in our service area, and the interstate and US 421 both connect it with Greensboro. Distance does not change how we handle a no-water call: the same checks happen in the same order wherever the well is.

Which county health department handles a flooded well in Kernersville?

For most of town, it is Forsyth County's health department, through its Environmental Health Division. Census maps put a small part of Kernersville in Guilford County, and homes there would work with Guilford County's health department instead. Either office can tell you about getting the water sampled once the flood has gone down and the well has been disinfected.

Our well near Abbotts Creek went under during a storm. Is the water safe once the pump runs again?

Not until it has been tested. NC DHHS says to test well water after flooding, since a flooded wellhead can let contaminants into the water. Leave the pump off until the flood recedes, have the well disinfected, then send a sample to a certified lab for bacteria. Until the results come back clean, use bottled water for drinking and cooking.

Is there any water left in the tank when the pump stops?

A little. The tank holds a modest amount of stored water, and some of it will still come out of the lowest tap until the pressure falls away. Save it for drinking and cooking. Once the gauge reads zero, nothing more will come until the pump runs again, so there is no point leaving taps open.

The pump runs, but no water comes out. What does that mean?

It usually means the water is leaving the system somewhere or never reaching it. The likely causes are a burst line in the yard, a broken drop pipe or coupling in the well, a worn-out pump end, or a well pumped down below the intake. Shut the pump breaker off so the motor does not run dry, then call.

Why did the water stop after the power went out and came back?

Power coming back on can hit the pump circuit with a surge, and a storm that knocked the power out may have sent lightning energy through the lines too. Pressure switches, capacitors, relays, and motors can all fail that way. Check the breaker once. If the pump still will not run, the fault needs a meter at the pressure switch and inside the control box.

Will you pull the pump on the first visit?

Only if the readings say the pump is the problem. Plenty of no-water calls end above ground, at the switch, inside the control box, or at a damaged wire. If the pump does need to come up, we explain what failed and what the work involves before anything happens, so there are no surprises halfway through.

Can a well run dry during a drought?

It can, especially a well that gives water slowly. Piedmont wells draw from fractures in the rock, and in a long dry spell some deliver less than a household pulls during heavy use. The pump then empties the well faster than it refills. Spreading out laundry and watering helps, and a drawdown and recovery test shows how much your well can keep up with.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.