Well Pump Repair in High Point, NC

Out past High Point's crowded center, where the county plan expects private wells and septic rather than community water, the water still depends on a pump in a well drilled into rock.

Map: High Point, NC in relation to GreensboroHigh PointGreensboro14.4 miJamestownArchdaleColfaxTrinityFORSYTHGUILFORD
Town
High Point, NC
County
Guilford County
From our Greensboro office
14.4 miles, straight line
Open High Point in Google Maps

When the gauge sits at zero, pressure fades halfway through a shower, or the breaker trips after a thunderstorm, that is well pump repair High Point homeowners cannot leave for next week.

What we check before anything comes out of the well

Most calls that sound like a dead pump turn out to be something smaller. A pressure switch with pitted contacts. A two-pole breaker that tripped and stuck. A start capacitor in the control box that swelled after a surge. A wire splice at the wellhead that corroded through. Each of those stops the water just as surely as a burned motor, and none of them means pulling the pump.

There are two kinds of pump in a home well system. A submersible hangs down in the well on a drop pipe, wired to the surface. A jet pump sits above ground and pulls water up through a suction line. Three-wire submersibles keep their start parts in a control box mounted near the pressure tank, so that box is one of the first things we test. Two-wire pumps carry those parts inside the motor, which leaves fewer parts to check up top and more reasons to pull the pump when it fails.

When the fault really is down the hole, repair means breaking the well seal, lifting the pump and pipe, and fixing or replacing the motor, the pump end, or the wire. North Carolina treats that as well contractor work. A certified contractor must be on site, and the well has to be disinfected once the pump is back in.

What a struggling pump takes down with it

A pump limping along on a bad part does not fail quietly. Every hard start heats the motor windings. A weak start capacitor makes each start harder, and the motor runs hot until its insulation breaks down. At that point a small part has turned into a whole pump.

Pressure switch contacts that chatter burn a little more with each cycle. Sooner or later they weld shut and the pump runs nonstop, or they burn open and the house goes dry with no warning.

The worst case is a pump that keeps pulling after the water in the well drops below its intake. Running dry wrecks the pump end and the motor quickly, and the grit a failing pump drags up ends up in the tank and the lines through the house.

Clues that point to the pump and its controls

Pumps rarely quit all at once. Most give you a few of these first:

  • Pressure that sags in the shower and never climbs back.
  • A breaker that trips, then trips again after one reset.
  • Air spitting from the taps, or water that runs, stops, and starts again.
  • Cloudy or gritty water from a well that has always run clear.
  • Clicking at the pressure switch while the gauge barely moves.
  • A power bill that creeps up with no other change, because the pump is running longer to do the same work.

If any of this began right after a lightning storm, mention it when you call. Knowing about the storm tells us where to start looking.

A pump repair visit, panel to wellhead

  1. We start with you: what the water did, when it changed, and whether a storm, an outage, or new irrigation came first.
  2. At the panel and the pressure switch, a meter shows whether power is reaching the pump and whether the switch closes when it should.
  3. On a three-wire system we test the capacitor and relay in the control box. On any pump we take amp draw and resistance readings on the pump wire.
  4. Those readings separate a bad motor from a bad wire or a worn pump end, before anything comes out of the hole.
  5. If the trouble is down the well, we open the cap, pull the drop pipe and pump, and repair or replace the part that failed.
  6. The pump goes back down, the cap is sealed, and the well is disinfected under North Carolina rules.
  7. We run the system through several full cycles with you watching the gauge, then explain in plain words what failed and what to keep an eye on.

Well pump repair in High Point, out where the city thins

High Point counted 114,059 people in 2020, and the plan Guilford County adopted in 2025 names it and Greensboro as the two most densely settled places in the county. The plan also says density drops off as you move away from those city centers. It is plain about what that means for water, too: the county is not a water provider, and where community water service is unlikely to reach, it points to private wells and septic systems.

Step back to the whole county and the picture gets more rural. Guilford covers about 658 square miles, and its own plan still calls it relatively rural. The cities and towns hold most of the people on less than half of the land. The rest is where a house depends on its own pump, its own pressure tank, and its own wiring, with no utility standing behind it.

That matters most in summer. When a thunderstorm rolls through and the power flickers, the surge runs down the service line into the pressure switch, the control box, and the motor. Lightning is one of the most common reasons pumps and control boxes fail anywhere in the Piedmont, and a home on a well takes that hit directly. Colfax, one of the nearby towns we also serve, sits under the same summer storms.

Scheduling, weekends, and the drive from Greensboro

We run the schedule from our office in Greensboro, Monday through Friday from 8am to 5pm. On a Saturday or Sunday, call or text (336) 613-4314 and say what the water is doing, whether the breaker trips, and whether you know if the pump is a submersible or a jet.

We come down I-85 out of Greensboro, which makes the High Point end of the county a straight run for us. A text with your street address and a photo of the pressure gauge and switch gets the visit started on the right foot.

ZIP codes we cover around High Point: 27260, 27262, 27263, 27265.

Questions from High Point

Still stuck? (336) 613-4314

Does Guilford County have to sign off on a pump repair?

No. North Carolina does not require a repair permit to fix or replace a well pump or tank, or for maintenance that leaves the well seal unbroken. Repairs to the well itself, such as casing work, go through Guilford County Environmental Health. Pump work still has to be done with a certified well contractor present, and the well gets disinfected afterward.

I live inside the High Point city limits but have a well. Do you still come?

Yes. If your water comes from a well on your own property, we work on it, inside the city limits or out in the county. What matters to us is the pump, the wiring, and the well, not the tax district. Give us the street address and a short description of what the water is doing.

Could a thunderstorm have killed my pump?

Yes. A strike nearby or a surge on the power line can burn out a pressure switch, a control box, or the pump motor itself. Sometimes only a capacitor goes and the fix is above ground. Sometimes the motor is gone. Tell us if the trouble started during or right after a storm, because that shapes what we test first.

How can I tell whether I have a submersible or a jet pump?

Look for a pump motor sitting near the pressure tank, in a well house, or under the house. If there is one, with pipe running from it toward the well, it is probably a jet pump. If all you see is a tank, a pressure switch, and maybe a gray control box on the wall, your pump is down in the well.

Will you repair my pump or tell me to replace it?

We test before we say either. A bad capacitor, switch, or splice gets repaired and the pump stays. A motor with failed windings, or a pump end worn past the point of holding pressure, usually makes replacement the better choice over another repair. We show you the readings and let you decide.

Do you work on well pumps in Colfax?

Yes. Colfax is one of the towns near High Point on our list, and a pump call there is the same job: find the fault, fix what failed, disinfect the well, and prove the system out before we leave. Call or text with your street address and what the water has been doing.

Is my water safe to drink right after a pump repair?

Not until the chlorine is gone. North Carolina requires the well to be disinfected after pump work, and the chlorinated water has to be run off before the system goes back to normal use. We will tell you how to flush it. A bacteria test after any repair is a sensible check, and we can help you arrange one.

What details help when I call about the pump?

Your street address, what the water did and when, and whether the breaker has tripped. If you can read the pressure gauge, give us the number. A photo of the tank, switch, and any control box helps too. Leave the pressure switch cover and the control box closed, since live power runs inside both.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.