Pressure Tank Replacement in High Point, NC

The pump clicks on, runs a few seconds, shuts off, and starts again every time someone fills a glass.

Map: High Point, NC in relation to GreensboroHigh PointGreensboro14.4 miJamestownArchdaleColfaxTrinityFORSYTHGUILFORD
Town
High Point, NC
County
Guilford County
From our Greensboro office
14.4 miles, straight line
Open High Point in Google Maps

In a house near High Point that draws from its own well, that rhythm usually means a waterlogged tank, and pressure tank replacement High Point well owners put off tends to end with a burned-out pump.

Replacing the tank that holds your pressure

The pressure tank is what lets a well act like a water system instead of a pump with a hose on it. Inside the steel shell, a rubber bladder or diaphragm holds water on one side and a cushion of air on the other. The pump fills the tank until the pressure switch reaches its cut-out setting, then stops. You draw from that stored water until pressure falls to the cut-in point, and the pump starts again.

All of that depends on the air charge. It should sit about 2 psi below the cut-in pressure: 28 psi on a 30/50 switch, 38 psi on a 40/60. When the bladder tears or the charge leaks away, the tank goes waterlogged, and every draw sends the pump through a quick start and stop.

Replacement means shutting the pump off, bleeding the system down to zero, removing the old tank, and setting a new one sized to your pump and household. The tank tee, gauge, relief valve, and shutoff get checked or renewed, and the new tank's pre-charge is set to your switch before any water goes back in. We also look over the switch itself while everything is open, since a switch that has chattered against a bad tank is often worn too.

What short cycling does to a pump

A waterlogged tank turns every glass of water into a pump start. Starting is the hardest thing a pump motor does: each start pulls a surge of current and heats the windings. Instead of a few long runs a day, the pump makes a constant string of short ones, and the motor wears out well ahead of its time.

The pressure switch contacts burn from the endless on and off. With a three-wire pump, the start parts in the control box wear too. In the shower, pressure swings from strong to weak and back. And a tank rusting from the bottom can split a seam and put its water on the floor, wherever that tank happens to sit.

Four signs you can check at the tank yourself

The gauge needle jumps. Watch the pressure gauge while someone runs a tap. With a healthy tank, the needle eases down for a while before the pump comes on. With a failed one, it drops to the cut-in pressure almost at once.

The switch clicks constantly. Rapid clicks from the pressure switch, a few seconds apart, are the sound of short cycling.

The tank sounds solid. Knock on the side of the tank, high up, with your knuckles. A healthy tank sounds hollow near the top where the air is. One that thuds all the way up is full of water.

The shell is weeping. Rust on the bottom seam, a damp spot under the tank, or a drip at the fittings means the steel is going.

One more sign only shows on a service visit: if pressing the air valve on top lets out water instead of air, the bladder has torn and the tank is done.

Tank replacement, one step at a time

  1. Confirm it is the tank. We test the air charge, the switch settings, and the pump before blaming the tank, because a worn switch can mimic a failed one.
  2. Shut down and bleed off. The pump breaker goes off, and we open a tap to bring the system down to zero pressure.
  3. Remove the old tank. It comes off its fittings and out of the house or well house, through whatever access the space allows.
  4. Charge and set the new tank. With the tank still empty, we set its air charge 2 psi below your cut-in pressure, then connect it with a new or reused tank tee, gauge, and relief valve.
  5. Bring the pressure back. Power goes on, the pump fills the tank, and we confirm the switch cuts in and out where it should.
  6. Check every joint. Each fitting is checked under full pressure. Then we show you how to read the gauge, so a tank losing its charge gets noticed early next time.

Pressure tank replacement in High Point homes that run on their own wells

Guilford County does not run water lines of its own. Its 2025 plan says any hookup to a community system takes coordination with regional partners, and where that service is unlikely, it plans on private wells and septic. In those homes no utility is holding pressure in the pipes. The tank and switch are the whole pressure system, and they belong to you.

Where the tank sits depends on how the house was laid out. North Carolina setback rules keep a private well at least 25 feet from the house, so the wellhead is out in the yard and a buried line brings water inside to the tank. Builders put the tank wherever they found room: a basement corner, a crawlspace, a garage wall, a utility closet, or a separate well house. Each one changes the job. A crawlspace tank has to come out through a small opening. A well house tank needs its pipe and fittings protected from freezing.

Age counts as well. By 2006, about 135,000 people in Guilford drew household water from wells, nearly double the county's 1990 figure of about 74,460. Any tank set during that growth and never replaced has been through a great many cycles, and the bladder inside does not last forever. We replace tanks around High Point and in nearby Jamestown and Archdale, and the first question is always how old the current one is.

Calling about your tank

High Point lies about 14.4 miles southwest of Greensboro, home of our office, as the crow flies. Tank work gets scheduled weekdays between 8am and 5pm. Saturday and Sunday, a call or a text to (336) 613-4314 is the way in.

It helps to tell us where the tank sits and to read off its label if you can see it. The size and model number let us bring the right replacement on the first trip. If the old tank is in a crawlspace, tell us roughly how big the opening is.

ZIP codes we cover around High Point: 27260, 27262, 27263, 27265.

Questions from High Point

Still stuck? (336) 613-4314

My house was built in the 1990s. Is the original pressure tank still all right?

It might be, but it has put in long service. Guilford County's well-water population nearly doubled between 1990 and 2006, and a tank installed back then has filled and emptied countless times since. Tap the tank, watch the gauge, and look at the bottom seam. If it short cycles or weeps, plan on replacing it before it takes the pump with it.

Why is my pressure tank inside when the well is out in the yard?

Because the well cannot sit right next to the house. North Carolina setback rules, which county staff in Guilford enforce, keep a private well at least 25 feet from the house. A buried line runs from the wellhead to the tank, and the tank goes wherever the builder had room: basement, crawlspace, garage, or well house.

Do you replace pressure tanks in Jamestown and Archdale?

Yes. Both towns sit next to High Point and are on our regular list. Give us the address and, if you can, the size printed on the tank label. A tank in a crawlspace or a well house is no problem; we just like to know before we load the truck.

Is topping off the air enough to fix my tank?

Sometimes. An older tank without a bladder needs air added now and then, and a bladder tank that has slowly lost its charge can be recharged if the bladder itself is sound. Water at the air valve tells you the bladder has torn, and air will not hold. Recharging is done with the pump off and the system at zero pressure, so it is a job we would rather do for you.

How big a tank do I need?

Big enough that the pump gets a real run each time it starts instead of short bursts. Size goes with the pump's output and the way your household uses water. A larger tank gives more drawdown between starts, which is easier on the pump. We size it from the pump and the switch setting, not from what fits the old spot.

Should my water be tested after a new tank goes in?

It is a good idea. EPA recommends testing right away whenever any part of the well system is replaced or repaired, plus a yearly test for total coliform bacteria, nitrates, total dissolved solids, and pH. A tank swap opens the system, so a bacteria test afterward is a sensible check.

How often should someone look at my tank and switch?

Once a year. The National Ground Water Association recommends a yearly checkup by a licensed or certified well professional that covers the pump motor, the pressure tank, and the pressure switch, along with a flow test and a water test for coliform bacteria and nitrates. Catching a tank that is losing its charge early can save the pump.

Can a bad pressure switch look like a bad tank?

Yes. A switch with pitted contacts can chatter, cut in late, or cut out early, and those symptoms overlap with a waterlogged tank. That is why we test the air charge, the switch, and the pump before deciding the tank has failed. Please leave the switch cover closed; there is live power under it.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.