Well owner tips, November 13, 2026

Your Yearly Well Maintenance Checklist

Nobody thinks about the well until the water quits. A short list, worked through once a year, catches most slow problems before they turn into a no-water morning.

Part of it you can do yourself in about 20 minutes. The rest belongs to a certified well professional and a certified lab.

What the NGWA yearly checkup includes

The National Ground Water Association recommends a checkup every year by a licensed or certified water well systems professional. Its list is a good one.

  • A flow test, to see how much water the system delivers and whether that has changed.
  • Pump motor performance. A motor working harder than it should often shows it here before it fails.
  • The pressure tank and pressure switch, including the tank's air charge and the switch settings.
  • An equipment inspection covering the wellhead, wiring, and controls.
  • A water test for coliform bacteria and nitrates.

The association also says owners should make sure the casing extends at least 12 inches above the ground and the cap is secure. That part is yours, and it comes next.

A walk around the wellhead you can do yourself

Pick a dry day and give it 10 minutes.

  • Cap. Seated firmly, free of cracks, with every bolt in place and the vent screen whole. Nothing should be able to crawl in.
  • Casing. At least 12 inches above ground, with no cracks, dents, or rust holes. String trimmers and mowers are hard on casing and on the conduit carrying the pump wire.
  • Ground. Sloped away from the well, with no puddle at the base after rain. Mulch and soil should not be heaped against the casing.
  • Nearby storage. Keep fuel, paint, fertilizer, and pesticides well away from the wellhead.

NC DHHS asks owners to check the wellhead once a year for cracks or openings, and EPA adds a warning worth repeating: never cut the casing off below ground level. If something looks wrong, take a photo before you call.

What to watch and listen for at the pressure tank

Stand by the tank while someone runs a tap in the house.

  • Note the gauge twice: once when the pump starts and once when it stops. A 40/60 switch should start near 40 psi and stop near 60 psi. Compare the readings with last year's.
  • Time the cycle. If the pump kicks on and off in quick bursts while the tap runs, it is short cycling, and a waterlogged tank is the usual reason.
  • Knock on the tank. The upper part should sound hollow. A tank that sounds solid all the way up may be full of water.
  • Check the base and fittings for drips, rust, or white mineral crust.

Look, listen, and write things down. Leave the pressure switch cover and the control box closed. Both hold live wiring, and the inside of either one is our side of the job.

A testing calendar built on the NC DHHS schedule

NC DHHS lays out a schedule that fits neatly on a calendar.

  • Every year: total and fecal coliform bacteria.
  • Every two years: heavy metals, nitrates, nitrites, lead, and copper.
  • Every five years: pesticides and volatile organic compounds, or yearly for a specific pesticide applied nearby.
  • Any time: after a repair or replacement of any well component, and after flooding.

In Virginia, the Department of Health puts testing squarely on the homeowner and says once a year is a good idea. On either side of the line, use a certified lab. Bacteria and nitrate cannot be seen, smelled, or tasted, so the lab report is the only way to know.

Keep a well folder and add to it every year

A plain folder in a kitchen drawer does more good than people expect. Keep these in it:

  • The well permit or certificate of completion, if there is one
  • Install dates and model numbers for the pump, tank, and any treatment equipment
  • Your switch settings and yearly gauge readings
  • Every lab report
  • Notes from each repair or service visit

When something goes wrong, that history shortens the diagnosis. When you sell, it answers the buyer's questions before they ask. Fall works well for the yearly visit, before freezing weather and holiday company. Call (336) 613-4314 to get on the schedule.

Quick answers

Still stuck? (336) 613-4314

Is a yearly checkup worth it if the water seems fine?

Most well trouble builds slowly. A tank loses air a little at a time, a pump motor starts working harder, a cap cracks, or bacteria get in without changing the taste. A yearly look catches those while the fix is still small, and the lab covers what nobody can taste.

What does a flow test actually measure?

How much water the system delivers over a set time at normal pressure. Compared with last year, it shows whether something changed. A drop can point to a worn pump, a clogged sediment filter, a pipe problem between the well and the house, or a well refilling more slowly.

Can I collect my own water sample for the lab?

For routine testing, many labs let you. Use their bottle, follow their instructions exactly, and do not touch the inside of the cap or bottle. Keep the sample cold and return it within the lab's time limit, since bacteria samples do not keep. For a home sale, use a certified sampler.

How often does a pressure tank need replacing?

There is no set schedule. A tank gets replaced when it fails: the bladder ruptures and the tank waterlogs, the shell rusts through, or it leaks at the fittings. Checking the air charge each year helps a tank last, and catching a waterlogged tank early saves the pump.

What time of year is best for the checkup?

Any time beats never, but fall works well. You catch problems before freezing weather, and a bacteria test after the summer storms tells you whether runoff found a way in. Pick a date you will remember, like the week you clean the gutters, and keep it.

Do I need to change a sediment filter on a schedule?

Go by what the filter tells you, not just the calendar. A cartridge that looks brown or slimy, or pressure that sags at the taps, means it is time. Homes with gritty water may need a new cartridge every few months, while others go much longer.

Should I shock chlorinate my well every year?

Not as routine maintenance. Shock chlorination is for a reason: a positive bacteria test, work that opened the well, or flooding. Doing it without a reason can mask a problem that a test would have caught. Test first, and disinfect when the results or the situation call for it.

Can a yearly check catch a failing pump before it quits?

Often. A motor drawing more current than it should, a flow rate that keeps falling, or a pump that runs longer to fill the tank can all show up at a yearly check. None of those is a sure sign of failure, but they give you time to plan instead of waking up to dry taps.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.