Pressure Tank Replacement in Colfax, NC

If the pump in your Colfax house kicks on every time someone rinses a cup, the pressure tank has probably lost its air cushion.

Map: Colfax, NC in relation to GreensboroColfaxGreensboro11.1 miKernersvilleOak RidgeHigh PointJamestownGUILFORD
Town
Colfax, NC
County
Guilford County
From our Greensboro office
11.1 miles, straight line
Open Colfax in Google Maps

That rapid clicking wears out the pump and the switch long before their time. Pressure tank replacement in Colfax is a smaller job than a pump, and it is often the repair that keeps the pump alive.

How a pressure tank holds pressure, and what a swap involves

The tank is a steel shell with a rubber bladder or diaphragm inside. Water fills one side. Compressed air sits on the other, and that air pushes water to your taps between pump starts. Without it, the pump has to run every time anyone opens a faucet.

The air side is pre-charged while the tank is empty, about 2 psi below the switch's cut-in pressure. On a 40/60 switch, that works out to about 38 psi. Over the years the bladder can leak or tear, or the air slowly escapes, and the tank fills with water. That is a waterlogged tank, and it causes short cycling.

Replacement means shutting off the pump, draining the system, and removing the old tank at the tank tee. The new tank is sized to your pump and household, pre-charged before it sees water, and fitted with a new tee, gauge, and drain. Old galvanized tanks with no bladder get replaced the same way, and their air control fittings come out with them. We look hard at the pressure switch on every tank job, since a failing tank works it to death. If the old tank sat on a damp floor, the new one goes up on a stand or pad so the shell stays dry.

Short cycling and the damage it spreads

Every start is the hardest moment in a pump motor's day. Current spikes, the windings heat up, and the switch contacts arc a little. A healthy tank keeps those starts spaced out. A waterlogged one turns a glass of water into a start and a shower into dozens of them.

The switch usually gives out first, with pitted or welded contacts that leave the pump stuck on or stuck off. Then the motor goes, and a tank job has become a pump job. Meanwhile the house gets pressure that surges and sags while you rinse your hair. A waterlogged tank also holds no reserve, so the moment the power blinks, every tap in the house goes flat.

A rusting tank adds its own trouble. When the shell finally lets go, it does so wherever the tank sits: on a basement floor, in a crawlspace, or beside whatever is stored in the garage.

A gauge needle that will not sit still, and other tank clues

  • Rapid on-and-off clicking from the switch while a single tap runs.
  • A gauge needle that drops and jumps back up again and again during a shower.
  • Pressure at the faucet that pulses instead of holding steady.
  • A tank that sounds solid all the way up when you knock on its side, a sign it is full of water.
  • Rust, sweating, or a damp ring at the base of the tank.
  • Water instead of air coming out of the valve on top when we press it. That means the bladder has failed.

A few of these can also point to a bad switch or a leak down in the well, which is why we test before replacing anything.

Changing out the tank in eight steps

  1. We watch the pump run through a cycle and note the cut-in and cut-out readings on the gauge.
  2. The pump's breaker goes off, and the system is drained down to zero.
  3. The old tank's air charge gets checked to confirm it is the culprit.
  4. We measure the space and pick a tank that fits it and matches your pump.
  5. Out comes the old tank. The new one goes in with a new tee, gauge, and fittings.
  6. The pre-charge is set on the empty tank to match your switch.
  7. The pressure switch gets inspected, and its feed tube is cleared. Burned contacts mean a new switch.
  8. Power goes back on. We watch several cycles, check every joint for leaks, and show you what a normal gauge swing looks like.

If the switch turns out to be the real problem, or a leak down the well is bleeding off pressure, you hear about it before a new tank goes in.

Pressure tank replacement in Colfax houses and where the tanks sit

Detached houses make up most of the housing in the ZIP area: about 1,883 of roughly 2,331 units, by Census estimates. A detached house on a well carries its own complete system, tank included. Nothing is shared with the neighbors, and no building manager looks after it. If the tank fails, it is your tank.

The same estimates put the median year built at about 2000. A tank that came with a house from that era has been holding pressure for a long stretch. Some have been replaced once already; some have not. When we arrive, one of the first things we want to know is whether the tank is original, a replacement, or something an earlier owner added.

Location matters as much as age. In the homes we work on, tanks sit in basements, crawlspaces, garages, utility closets, and now and then a small well house. A crawlspace tank has to fit through the access opening. A garage tank may need protection from a bumper. Tell us where yours sits when you call.

One more wrinkle: Guilford County's GIS shows that ZIP area reaching into the city limits of Greensboro, High Point, Kernersville, and Oak Ridge. A mailing address can land inside a city or outside one, so it does not tell you whether a house runs on a well. A pressure tank and gauge in the house do.

Getting a tank swap on the calendar

Sandy Ridge Road is one of the ways we reach Colfax homes from Greensboro, and we work in High Point and Jamestown as well. Office hours run 8am to 5pm, Monday through Friday. On a weekend, a call or a text gets through.

Call (336) 613-4314 and tell us where the tank sits, roughly how big it is, and whether the pump has been clicking on and off. A photo of the tank and its gauge, sent by text, helps us bring the right parts.

ZIP code we cover around Colfax: 27235.

Questions from Colfax

Still stuck? (336) 613-4314

How do I find out whether city water is available to my Colfax property?

Guilford County's water service page says public water in the county comes from Greensboro, High Point, Jamestown, the Sedgefield Sanitary District, Burlington, and Stokesdale. It tells property owners to call Greensboro Water Resources to learn whether city water is available at a given address. Until a line actually serves your lot, the well and its tank are your supply.

Does replacing a pressure tank in Guilford County need a permit?

No repair permit is needed. North Carolina law does not require one to repair or replace a well pump or tank, or for maintenance that does not open the well seal. Work that does open the well for a repair is a different matter. That goes through Guilford County Environmental Health, which oversees well construction and repairs in the county.

We live off Sandy Ridge Road near the farmers market. Is that in your area?

Yes. The Robert G. Shaw Piedmont Triad Farmers Market carries a Colfax address on Sandy Ridge Road, and we work on wells for the homes around it. When you call, give the office the nearest crossroad along with your street address, so the technician goes straight to the right driveway.

How long should a pressure tank last?

There is no fixed number. A tank lasts until its bladder leaks or its shell rusts through, and short cycling, sediment, and a wrong pre-charge all speed that up. The National Ground Water Association recommends a yearly checkup that includes the pressure tank and switch, and a check like that catches a fading tank early.

Can I check the air charge in my tank myself?

Reading the gauge is easy and safe. A true air-charge check is different. The pump has to be off at the breaker and the system drained to zero before the reading means anything, and the switch cover should stay on the whole time. Most people would rather let us do it, and we check it on every tank and pump visit.

Why would a new tank start short cycling within a year?

Usually the pre-charge was never set to match the switch, or the real problem was somewhere else. A leaking check valve or a split drop pipe lets pressure bleed off, and the pump restarts with no tap open. A clogged switch tube can also cause rapid cycling. We look at all three before blaming the tank.

What tank size fits my house and pump?

It should match the pump's output and how your household uses water. A larger tank gives more drawdown between starts, so the pump runs less often and for longer stretches, which is easier on the motor. The limit is usually space, especially in a crawlspace or closet. We size it to both.

Is a rusty pressure tank something to worry about?

Surface rust on the outside is common. Rust at the bottom seam, pinhole leaks, or a tank that sweats and drips is another story. Those shells can split without much warning and soak whatever is around them. If you see wet rust at the base, call before the tank picks the timing for you.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.