Pressure Tank Replacement in Oak Ridge, NC

A switch that chatters on and off every time someone opens a tap, and a shower that swings from strong to weak, usually trace back to the pressure tank rather than the well.

Map: Oak Ridge, NC in relation to GreensboroOak RidgeGreensboro13.2 miStokesdaleColfaxSummerfieldKernersvilleGUILFORD
Town
Oak Ridge, NC
County
Guilford County
From our Greensboro office
13.2 miles, straight line
Open Oak Ridge in Google Maps

Pressure tank replacement in Oak Ridge is a contained job, but first we sort out whether the tank is yours, because a large share of homes here get water from a community system instead.

Inside a well tank, and why the air charge matters

A pressure tank is a steel shell with a rubber bladder or diaphragm inside. Water fills the bladder. Air trapped around it gets squeezed as the pump runs, and that squeezed air is what pushes water to your taps after the pump shuts off. Without it, the pump would start for every glass of water.

The air side gets set about 2 psi below the cut-in pressure of the switch. On a 40/60 switch, that means 38 psi with the tank empty. Over the years a bladder can tear, or the air can leak out through the valve or a pinhole in the shell. Once the cushion is gone, the tank is waterlogged and the pump short cycles. Older galvanized tanks with no bladder work on the same idea, but they need their air topped off now and then.

Replacement means shutting off the pump circuit, relieving the pressure, disconnecting the old tank, and setting a new one sized to the pump. We set its precharge, look over the parts on the tank tee (pressure switch, gauge, and relief valve), replace any that are worn, and bring the system back up. The well itself stays sealed the whole time.

What a waterlogged tank does to the pump down the well

The tank is the pump's shock absorber. When it fails, the pump takes the beating.

With no air cushion, the pump starts the moment you open a tap and stops the moment pressure spikes, sometimes several times a minute. Each start sends a surge of current through the motor and arcs the switch contacts. Run that way for a few months and you can burn up a pressure switch, overheat a motor that should have had years left, and end up needing a pump where a tank would have done.

Old tanks also fail outward. A rusted shell weeps at a seam or at the base, then lets go, and a crawlspace or basement floor takes on water until somebody notices.

When pressure tank replacement in Oak Ridge is the right fix

You can spot a lot of tank trouble without a single tool.

  • The gauge needle swings from low to high in a few seconds while one tap runs.
  • The switch clicks on and off in a quick rhythm during a shower.
  • Knock on the side of the tank. A healthy one sounds hollow near the top. A waterlogged one sounds solid all the way up.
  • Rust streaks, damp spots, or a puddle at the base.
  • The tank is old enough that nobody in the house remembers it going in.

A few of these have other possible causes. A switch out of adjustment, a check valve leaking back down the well, or a plugged switch tube can also cause rapid cycling. That is why the tank gets tested before it gets replaced.

Swapping the tank, from shutoff to first cycle

First we prove the tank is the problem. We watch the gauge through a few cycles, then cut power to the pump, let the system down to zero, and check the air side with a gauge. A tank that reads near nothing, or spits water from its air valve, has a failed bladder.

Next comes sizing. A tank that matches the pump's output lets the motor run longer and start less often, which is easier on it. If your old tank was too small from the start, we will say so and size up. We also look at where it sits. The new tank needs a level spot, protection from freezing, and room to work on it later.

Then the swap. The old tank comes off, the new one goes in with its precharge set to the switch, and worn tank tee parts get replaced while everything is apart. We bring power back, watch the pump fill the tank, and check that the switch cuts in and out at the right pressures. Before we go, you get the numbers: switch setting, precharge, and what the gauge should read.

Private well, community system, or town water: who owns the tank

Before anyone orders a tank, we need to know whose system it is. When the mayor laid out the town's water picture in 2019, about a third of Oak Ridge residents got their water from community wells run by private utility companies. On a community system the pumps, tanks, and pressure controls belong to the operator. A pressure problem there is theirs to chase, and your first call should go to them.

The picture keeps shifting. The town took over the Honeycutt Reserve subdivision's community well system in December 2022, and those homes became the first customers of a municipal system Oak Ridge is still building. New housing here has typically arrived in tracts where the developer supplies a shared well.

That leaves the homes on their own wells, and those are the tanks we replace. Across Guilford County, groundwater use grew sharply. A 2007 county health department report estimated that about 135,000 residents relied on it in 2006, up from about 74,460 in 1990. If your house went up during that stretch and still has its first tank, that tank has put in long service and deserves a look.

Getting a tank replacement booked

On a weekday between 8am and 5pm, a call to (336) 613-4314 reaches the office, where we keep the schedule. Saturday and Sunday, call or text and we will get back to you.

Two details help us bring the right tank on the first trip: the size printed on your old tank's label, and where it sits, whether that is a basement, a crawlspace, a garage, or a well house. A photo by text does the job. We come up from Greensboro, northwest toward Oak Ridge, and use NC 150 to get across town. We also replace tanks in Colfax.

ZIP code we cover around Oak Ridge: 27310.

Questions from Oak Ridge

Still stuck? (336) 613-4314

I'm on a community well in Oak Ridge and my pressure is weak. Should I call you?

Call the system's operator first. On a community well, the pumps, storage, and pressure controls belong to the utility, and low pressure across the system is theirs to fix. If you have a tank and pump of your own on a private well, or you aren't sure which setup you have, call us and we will help you sort it out.

Is a Guilford County permit needed for a new pressure tank?

No. North Carolina law does not require a repair permit to repair or replace a well pump or tank. Tank work happens above ground, and the well seal never gets opened. Permits from Guilford County Environmental Health cover building, repairing, and abandoning the well itself, which a tank swap does not touch.

My home is in Honeycutt Reserve. Is the water pressure my responsibility?

The Honeycutt Reserve community well system was turned over to the Town of Oak Ridge in December 2022, so the system and the pressure it delivers are the town's to manage. Pressure problems that come from the system go to the town. Our work is on privately owned wells and the tanks, pumps, and switches that go with them.

How often should a well pressure tank be checked?

Once a year is a good rhythm. The National Ground Water Association recommends a yearly checkup by a licensed or certified water well professional that covers the pressure tank and pressure switch, along with pump performance, a flow test, and a water test. A tank that gets its precharge checked regularly tends to last longer.

Will pumping air into a waterlogged tank fix it?

On a bladder tank, usually not for long. If the bladder has torn, water sits on both sides of it, and any air you add will be gone within days. Older tanks without a bladder are a different case, and those can be recharged. We check the precharge with the system at zero, which tells us which situation you have.

What size tank does my house need?

That depends more on the pump's output and the switch setting than on the size of the house. The goal is a tank that holds enough water between cut-in and cut-out for the pump to run a minute or more each cycle. Bigger tanks mean fewer starts. We size it on site once we know what pump you have.

My tank is in a crawlspace. Can it be replaced there?

Yes, as long as there is room to work and a way to get the old tank out. Plenty of tanks live in crawlspaces and do fine there, provided they are protected from freezing. If the space is tight, or the tank keeps getting bumped or soaked, a replacement is a good time to talk about moving it.

Would replacing the tank cure weak water pressure?

Only if the tank is the cause. A waterlogged tank brings pressure swings and short cycling, but steady low pressure usually comes from the switch setting, a worn pump, a clogged filter, or a restriction in the line. We test before recommending a tank, so you are not left with new equipment and the same weak shower.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.