For a home that runs on its own well, emergency well service in Greensboro starts with a phone call and a few safe checks you can make before we arrive. Often the cause is above ground, and finding it beats guessing at it.
Tracking down why the water stopped
Every no-water call starts with one question: is the trouble above ground or down in the well? Above ground means the breaker, the pressure switch, a three-wire pump's control box, the wiring, or the tank. Down the well means the pump, the wire and splice, the drop pipe, or the water level itself.
We work from the top down, because the top is where the quick fixes are. A tripped breaker, burned switch contacts, or a failed start capacitor can be found and fixed without pulling anything. Lightning and power surges are a common cause of control box and pump failures, so after a storm that is one of the first things we check. If the top end tests good, we measure the pump circuit to learn whether the motor, the wire, or the splice has failed.
Sometimes the equipment is fine and the well is the problem. A pump that runs but moves no water can mean the water level has dropped below the pump. That calls for a different fix, and you will hear plainly which one you are facing.
Why a dry house gets worse the longer it sits
Dry running overheats a pump quickly. If the switch sticks closed and the pump keeps running against a dry well or a split pipe, the motor can burn itself up. A switch repair becomes a pump replacement.
A breaker that keeps getting reset is a warning of its own. Each reset pushes power into a motor or wire that may already be shorted, and that can do more damage down the hole. One reset is reasonable. After a second trip, leave the breaker off.
A dry house is also hard to stay in for long, especially with young children or older family at home. And the longer a fault sits, the more parts it tends to take with it.
What the gauge and the breaker are telling you
What you notice in the first few minutes narrows the list. Pass it along when you call.
- Gauge at zero, pump silent: usually power, the pressure switch, or the control box.
- Gauge at zero, pump running: a dry pump, a broken pipe, or a falling water level.
- Well breaker tripped: a possible short in the pump, the wire, or the control box.
- Water came back after an hour, then quit again: often a water level problem, or a jet pump losing its prime.
- Pressure faded for days before it stopped: a worn pump, a leak, or a waterlogged tank finally giving out.
- Sputtering, air, or muddy water just before it stopped: the pump is drawing air or sediment.
What to do before we arrive, and what we do once we are there
Before we get there
- Read the pressure gauge near the tank and write down the number.
- Check the breaker panel. If the well breaker has tripped, reset it once and only once.
- Leave the pressure switch and the control box closed. Both carry live current.
- If the wellhead was under floodwater, keep the pump's power off until the water goes down.
- Fill some jugs at a neighbor's house, or pick up a few gallons to drink and cook with.
- If we will pull in after dark, turn on an outside light near the well.
Once we arrive
- We check power at the panel, then at the switch and the control box.
- We read the air charge in the tank and look for signs it is waterlogged.
- We test the pump circuit to see whether the motor, wire, or splice has failed.
- If the trouble is down the well, we lay out the options before anything gets pulled.
- When water is back, we run the system through a full cycle and tell you whether the water should be tested before you drink it.
Emergency well service in Greensboro, out where the wells are
Greensboro counted 299,035 people in the 2020 Census. In a city that size, it is easy to forget that some households still depend on a pump in the yard. When one of those pumps quits, there is no city connection to switch over to. The house is simply dry until the well runs again.
Low ground is part of the picture, too. Haw River State Park, which lies in Rockingham and Guilford counties about 15 miles north of the city, includes wetlands and a floodplain swamp. Wherever water collects after heavy rain, a wellhead can end up under it, and a flooded well is a special case. NC DHHS says not to turn the pump's electricity back on until the floodwater recedes, and it strongly recommends calling the local health department or a licensed well driller to shock chlorinate the well. It also says to test the water after a flood, since contaminants can get in while the wellhead is submerged.
Getting across town is rarely the hard part. Our base is here, and I-40, I-85, and I-73 put every edge of the city close at hand. Tell us the nearest exit or main road when you call.
Calling us when the house is dry
Call (336) 613-4314. During the week, from 8am to 5pm, we take the call and fit it into the schedule. Over the weekend, text or call that same number, and leave the address in the message.
We head out from our base in Greensboro, so the trip to any side of the city starts close by. If you are not sure whether your house is on a well or on city water, call anyway, and we will help you sort it out over the phone before anyone drives out.
ZIP codes we cover around Greensboro: 27395, 27401, 27403, 27405, 27406, 27407, 27408, 27409, 27410, 27455, 27495.