Well Pump Replacement in Greensboro, NC

Out on the edges of Greensboro, where houses still run on private wells, the pump in the well may be the one that came with the house.

Map: Greensboro, NC in relation to GreensboroGreensboroSummerfieldJamestownBrowns SummitGUILFORD
Town
Greensboro, NC
County
Guilford County
From our Greensboro office
In town
Open Greensboro in Google Maps

When it finally quits, or keeps quitting after repairs, well pump replacement in Greensboro means pulling the old unit, matching a new one to your well, and getting water back to the taps.

Pulling the old pump and setting the right new one

Replacing a pump starts with knowing which kind you have. Most drilled wells in the Piedmont run a submersible pump that sits down in the well on a drop pipe, with wire running back up to the house. Some older homes use a jet pump instead, which sits above ground and pulls water up through the line.

With a submersible, the pump, pipe, and wire all come up through the wellhead, and we look at every piece on the way out. Brittle pipe, a corroded splice, or a worn torque arrestor gets replaced while the line is out of the hole. Then the new pump is matched to what the well can give and what the house uses. A three-wire pump needs a control box built for it. A two-wire pump runs without one. Mix those up and motors burn out.

North Carolina does not require a repair permit to replace a well pump. It does require a certified well contractor on site for the work, and it requires the well to be disinfected when the pump goes back in.

Nursing a failing pump until it quits on its own schedule

A pump near the end usually warns you, and it is tempting to nurse it along. The trouble is how it finally goes. A motor that is drawing too hard can trip the breaker, cook the control box on a three-wire system, or burn through the splice down in the well. A planned swap on a weekday turns into a no-water call on whatever morning the motor picks.

A tired pump also runs longer to refill the tank. Those long runs wear the switch contacts and heat the motor. If the pump has started pulling sand or grit, that sediment ends up in your lines and in any filter or softener downstream.

When a pump is past repairing

Most pump trouble gets repaired, not replaced, and that is how it should be. A bad pressure switch or a failed capacitor in the control box is a repair. The pump itself is worth replacing when you see a few of these together:

  • The well breaker trips when the pump starts, or trips again soon after a repair.
  • Pressure fades during a shower and takes a long time to recover.
  • The pump keeps running well after everyone has stopped using water.
  • Air spurts from the taps, or the water turns cloudy or gritty after a long run.
  • The same pump has been repaired more than once in the last few years.

In Greensboro, the age of the house is a fair clue as well. A home that went on a well while groundwater use was climbing across the county may still have its first pump. That alone is no reason to replace a working pump, but it is a good reason to have it checked.

A pump replacement visit, step by step

  1. A few questions first. We ask what you are seeing, how old the house is, and whether you have any paperwork on the well.
  2. Test before pulling. We check the breaker, wiring, pressure switch, control box, and tank. There is no sense pulling a good pump to fix a bad switch.
  3. Pull the pump. The pump, drop pipe, and wire come up out of the casing, and we look at each piece as it surfaces.
  4. Pick the replacement. Horsepower, voltage, and wiring get matched to the well and the house.
  5. Set the new pump. A new splice, safety rope, and torque arrestor go on, and the assembly goes back down to the right setting for your well.
  6. Disinfect the well. State rules call for a chlorine dose of at least 100 parts per million that stands in the well for 24 hours or more, followed by pumping until no chlorine is detected.
  7. Run the whole system. We set the tank's air charge, confirm the switch settings, and watch a full cycle from cut-in to cut-out.

NC DHHS also recommends testing the water after any well component is repaired or replaced, since opening a well can let contaminants in.

Well pump replacement in Greensboro, old wells and new

Guilford County's long-range plan, adopted in 2025, says Greensboro and High Point have the greatest population densities in the county, with homes spreading thinner the farther you get from those centers. The thinning edge is where the wells are: houses beyond the city lines, each with its own pump, pipe, and tank.

Those wells span a lot of years, and the age changes what comes out of the hole. A 2007 county health department report estimated that about 135,000 Guilford County residents relied on groundwater for their household water in 2006, up from about 74,460 in 1990. Wells that date from that stretch may still carry their original pump, wire, and drop pipe.

Paperwork depends on age, too. The Guilford County Board of Health enacted its first local well rules effective June 1, 1989, with permits and local inspection of construction. State law has required permitting, inspection, and testing for wells built or repaired on or after July 1, 2008. A well older than the 1989 rules may have no construction record at all, so we size the new pump by testing what the well actually does. A newer well may come with permit records that save some guesswork.

Either way, the new pump gets matched to the well you have, not the one on paper.

Getting us out to your side of Greensboro

We are based in Greensboro, so the edges of the city are close to home for us. US 220 carries us north and south, and US 421 covers the northwest and southeast sides. Give us the nearest crossroad when you call, along with the street address.

Office hours run Monday through Friday, 8am to 5pm. On Saturday and Sunday, call or text. The number is (336) 613-4314. If the pump is still limping along, say so. If it has already quit and the taps are dry, say that first.

ZIP codes we cover around Greensboro: 27395, 27401, 27403, 27405, 27406, 27407, 27408, 27409, 27410, 27455, 27495.

Questions from Greensboro

Still stuck? (336) 613-4314

Do I need a Guilford County permit to replace my well pump?

No. North Carolina does not require a repair permit to replace a well pump or a pressure tank. Guilford County Environmental Health does require a permit application for well repairs, such as fixing a cracked casing. If we find a problem with the well itself while the pump is out, we will explain what that means before any other work starts.

Can the county test my water after the new pump goes in?

Yes. Guilford County Environmental Health offers private well testing for bacteria, inorganics, petroleum, pesticides, and nitrates and nitrites. Staff come to your home, inspect the well, and collect the samples themselves. The office does not accept samples that homeowners bring in, so plan on scheduling a visit. A bacteria test is the one to start with after pump work.

My well is older than the county's 1989 well rules. Can it still take a new pump?

Usually, yes. What matters is the condition of the casing, how much water the well gives, and whether the old pump setting still makes sense. An older well may have no construction record, so we learn what we need from testing the well and from what comes up with the old pump.

How long should a submersible pump last?

There is no honest single number. A pump's life depends on how often it starts, how hard it works against the well, what is in the water, and how well the rest of the system protects it. A properly sized pump with a healthy tank starts less often and runs cooler. Short cycling is the fastest way to shorten its life.

Will you swap the tank too when you put in the pump?

Only if it needs it. We check the tank's air charge and bladder while we are there. A waterlogged tank makes a new pump start and stop constantly, which wears it out early, so a failed tank should go. A tank that holds its charge and is in good shape can stay.

Is the water safe to drink right after the new pump is in?

Not right away. The well gets a strong chlorine dose after pump work, and it has to be pumped out until no chlorine is detected. After that, a bacteria test is the surest way to know the water is clean. Until the result comes back, bottled water for drinking and cooking is a sensible precaution.

Could my jet pump be traded for a submersible?

Often it can, if the well is drilled, has room in the casing for a submersible, and the wiring can be run down to it. A submersible is quieter, stays out of the way, and does not lose its prime. Some shallow wells and some older setups are better left on a jet pump. We look at the well before recommending either one.

Why not just put in the biggest pump that fits?

Because a pump that moves more water than the well can supply will pull the water level down to its intake. That means sputtering, air in the lines, and a motor running hot. An oversized pump also short cycles against a small tank. The right pump fits what the well gives and what the house actually uses, with a little room to spare.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.