Well Pump Replacement in Summerfield, NC

Plenty of wells in northwest Guilford County went in during the building years of the 1990s and 2000s, and an original pump from that stretch has put in a long career.

Map: Summerfield, NC in relation to GreensboroSummerfieldGreensboro11.1 miStokesdaleOak RidgeColfaxGUILFORD
Town
Summerfield, NC
County
Guilford County
From our Greensboro office
11.1 miles, straight line
Open Summerfield in Google Maps

When an old motor starts tripping the breaker or can't build pressure anymore, a planned well pump replacement Summerfield families schedule on their own terms beats waiting for it to die on a Sunday.

Planning the well pump replacement Summerfield wells eventually need

Replacing a pump starts before anything comes out of the ground. The new pump has to match the well, the house, and the wire already in place: horsepower, voltage, two-wire or three-wire, and a flow rating the well can keep up with. A pump that outruns the well draws it down and runs dry. One that is too small leaves you with weak pressure upstairs.

On the day of the swap, the drop pipe, wire, and old pump come up out of the casing one length at a time, and everything that comes up gets looked at. Old steel pipe that has rusted thin, wire with cracked insulation, a tired check valve, or a worn torque arrestor gets replaced rather than lowered back down to fail later. With a three-wire pump, the control box is usually changed out too so the parts match.

After the new pump is set and wired, North Carolina rules call for disinfecting the well. The chlorine has to reach at least 100 parts per million in the well and stand for 24 hours or more, and the well is then pumped until no chlorine shows before the water goes back into use.

Running a worn-out motor until it gives up on its own

An old pump rarely fails gently. It runs hotter, draws more current, and builds pressure more slowly until the breaker trips one day and stays tripped. That day is never one you picked.

The bigger worry is what holds the pump up. Galvanized drop pipe rusts from the inside, and when it finally lets go, the pump and pipe can drop down the well. Fishing them back out is slow, careful work, and sometimes a dropped pump cannot be recovered at all. A tired motor can also cook its own wire splice or pull more current than the switch contacts were made for, so the damage spreads to parts that were fine.

When the motor itself is the part that is failing

Some symptoms point past the switch and tank to the pump. The breaker trips at start-up even with a new switch in place. The motor draws more amps than its nameplate allows, or the reading jumps around. Pressure climbs slowly and tops out short of the cut-out setting, so the pump never shuts off on its own.

Others you can notice from the kitchen. Water runs strong for a minute, fades, then comes back. Sand or grit shows up where it never did before, which can mean worn pump parts or a well that is changing. The pump has needed repairs twice in a short span. Or the paperwork shows the pump went in when the house was built, decades back.

None of these prove the motor is done on their own. Readings do, and that is why we test before recommending a replacement.

Replacement day at the wellhead, in order

Before the pull

We confirm the diagnosis with electrical readings, look at the tank and switch, and check that the wellhead leaves room to work. We will have asked about access when you called, since the truck may need to get close to the well.

At the well

We shut off and lock out the pump circuit, open the cap, and lift the old pump, pipe, and wire out, inspecting each piece on the way up. The new pump goes together with a fresh splice kit, a check valve, and any pipe or wire that needs replacing, then gets lowered back to the same setting unless the old one was set wrong.

Start-up and disinfection

With the cap back on and sealed, we start the pump, watch the amp draw, and set the switch and tank pre-charge to match. Then we chlorinate the well and explain how and when to run the water clear. You keep a note of the new pump's model and setting for your records.

Farm-era wells, older lots, and community systems in Summerfield

This is a young town with an old footprint. The community traces back to 1769, when Charles Bruce bought 640 acres in what is now the heart of town, and for much of the 1800s it was farm country growing corn, tobacco, and livestock. The town itself was not incorporated until 1996. A pump call here can mean an older farmhouse well or one put in for a house built a few years ago.

The years in between matter most for replacements. A 2007 Guilford County health report, quoted in the town's 2010 plan, estimated that about 135,000 county residents used groundwater at home in 2006, up from about 74,460 in 1990. The same report noted many large community wells going into new developments, particularly in the northwest part of the county, including this area, Oak Ridge, and Stokesdale. The town's zoning still carries older RS-40 and RS-30 lots of record, with 40,000-square-foot and 30,000-square-foot minimums. A pump set during that build-out and never replaced has had a long run.

Guilford County's own well rules first took effect on June 1, 1989, bringing local permits and inspections. A well older than that went in before the county inspected construction under its own rules. That is not a defect by itself, but when the pump comes up, we look harder at the casing and cap.

Setting up a replacement with our office

The office is open Monday through Friday, 8am to 5pm, and we can put a replacement on the calendar or answer questions about what to expect. Call or text (336) 613-4314. On Saturday and Sunday a call or text still reaches us, so describe what the pump is doing. Coming from Greensboro, we usually take I-73 north toward town. If you know roughly when the pump went in, or have the old paperwork, keep it handy for the visit.

ZIP code we cover around Summerfield: 27358.

Questions from Summerfield

Still stuck? (336) 613-4314

Our Summerfield neighborhood is on a community well. Who replaces the pump?

Usually not you. A community well serves a group of homes, and its pump and equipment belong to the system's owner or operator, so that is the first call. If you are not sure which kind of system you have, the closing papers or the operator can tell you. If your house has a private well on its own lot, the pump is yours, and so is the choice of who replaces it.

Should we test the water after a new pump goes in?

Yes. NC DHHS recommends testing after any well component is repaired or replaced, since opening a well can let contaminants in. Guilford County Environmental Health offers private well sampling, and its staff come out, look the well over, and take the samples themselves; the office will not accept bottles that residents bring in. Wait until the disinfection chlorine has been run out before anyone samples.

How can we tell whether our well predates Guilford County's well rules?

Start with the age of the house. The county's first local well rules took effect June 1, 1989, so a home built before then likely has a well that went in before local permitting and inspection. Closing papers or an old permit can confirm it. An older well is not a bad well, but it earns a closer look at the casing and cap while the pump is out.

While the pump is out, should the tank be changed too?

Not automatically. If the tank holds its air charge and the bladder is sound, it stays. A waterlogged or rusting tank, though, will short cycle the new pump and cut its life short, so replacing both at once makes sense then. We check the tank on every pump job and give you a straight answer either way.

Could a submersible take the place of our old jet pump?

Often, yes. Jet pumps sit above ground and pull water up, which limits how far they can lift it. A submersible pushes water up from inside the well and usually runs quieter and steadier. Whether the change makes sense depends on the well, the casing size, and the wire run to the house, and we look at all three before recommending it.

Can a stronger pump pull more water from our well?

Only up to what the well can deliver. Every well refills at its own pace, and a pump sized past that pace just empties the well faster and risks running it dry. If you need more water, a drawdown and recovery test measures what the well can really give, and that number guides the pump choice.

Is the old wire reused when the pump is replaced?

Only if it tests good. Wire that has hung in a well for decades can have cracked insulation or corroded splices, and a new pump on bad wire fails early. We test the wire with a meter before deciding. When the run from the house to the wellhead is long, we also confirm the wire is sized right for the new motor.

Why did our last pump wear out so early?

The usual suspects are short cycling from a waterlogged tank, lightning or power surges, a pump sized larger than the well could feed, and sand wearing the impellers. Low voltage from undersized wire also cooks motors. When we replace a pump, we look for the cause so the new one does not meet the same end.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.