Pressure Tank Replacement in Gibsonville, NC

Click, run, stop. Click, run, stop. When the well pump fires up every time someone rinses a glass, the pressure tank has usually lost its air charge.

Map: Gibsonville, NC in relation to GreensboroGibsonvilleGreensboro14.1 miElonWhitsettBurlingtonALAMANCEGUILFORD
Town
Gibsonville, NC
County
Guilford County
From our Greensboro office
14.1 miles, straight line
Open Gibsonville in Google Maps

Pressure tank replacement in Gibsonville comes up at homes outside the reach of town water, where that tank is all that stands between your pump and a day full of needless starts.

How pressure tank replacement in Gibsonville works

Your well pump does not run every time you open a faucet. The pressure tank holds a reserve of water under pressure, with a cushion of air on the other side of a rubber bladder or diaphragm. As you draw water, that air pushes it out, and the pump only starts when pressure falls to the switch's cut-in point. Common settings are 30/50 and 40/60 psi.

The air cushion is the whole point. It is charged slightly below the cut-in pressure. When the bladder tears or the air leaks away, water fills the tank, the cushion disappears, and the pump starts and stops in quick bursts. That is short cycling.

Replacement means draining the old tank, disconnecting it at the tank tee, setting a new one, charging its air side to suit your switch, and reconnecting the gauge, relief valve and drain valve. Going up a size is often worth it, since a larger tank means fewer starts.

Short cycling wears out the pump, not just the tank

Each pump start is a jolt of current and heat. A waterlogged tank can turn a handful of starts during a shower into dozens. The submersible motor takes that abuse, and so do the pressure switch contacts, which pit and burn a little with every extra cycle.

Tanks also leak as they age. Rust works through from the inside, and the first sign is often a slow drip under the tank or a stain on the floor. In a crawlspace, that leak can go unnoticed for weeks, soaking the soil and the framing nearby.

Left alone, a dead tank usually takes the pressure switch with it first and the pump after that, and the pump is the part that sits deepest and is hardest to reach.

Telltale signs of a waterlogged or leaking tank

A tank on its way out leaves clues around the house:

  • The pressure gauge needle swings quickly between low and high instead of easing down.
  • The pressure switch clicks on and off over and over while one tap runs.
  • Shower pressure pulses strong and weak.
  • The pump runs in short bursts even when nothing more than a toilet is refilling.
  • The tank sounds solid when tapped all the way to the top, instead of hollow near the upper half.
  • Rust at the seams, a wet base or a puddle under the tank.
  • Water, not air, spits out when the air valve on top is pressed.

A couple of these can also come from a failing switch or a clogged tank tee, which is why we test the whole setup instead of assuming.

Swapping a pressure tank, step by step

  1. Before touching anything, we watch the gauge through a few pump cycles to confirm the tank is the problem and not the switch or the pump.
  2. We kill power to the pump at the breaker and drain the system down.
  3. The old tank is disconnected at the tank tee and carried out, which takes some care in a tight crawlspace or closet.
  4. The new tank goes on a stable base, and its air side is set about 2 psi below your cut-in pressure while it is still empty.
  5. We reconnect, replacing a worn gauge, relief valve or drain valve on the tee if needed. If the pressure switch contacts look pitted or burned, we show you, since a switch that rode through months of short cycling is often close to failing too.
  6. With power back on, we watch the pump fill the tank and shut off at the right pressure, then run water to confirm the pump now rests between starts.

Town meters, private tanks and a county line in Gibsonville

Most homes on the town system never need a pressure tank. The Town of Gibsonville buys its water from the City of Burlington and moves it through the town's own lines, and its 2025 Local Water Supply Plan counts about 4,323 metered residential connections. Those homes get their pressure from the public system.

Step beyond the last meter and the job of holding pressure moves into your house. A private tank works every time anyone opens a tap or starts a load of laundry, so it carries a big share of the system's daily wear. Because it often sits out of sight, in a crawlspace, a utility closet or a well house, a failing tank can go a long time before anyone looks at it.

The town also straddles a county line. The 2020 Census counted 4,642 residents in the Guilford County part of town and 4,278 in the Alamance County part. For a tank job, which side you are on changes nothing about the work: the parts, the air charge and the testing are the same in both counties. What changes from house to house is access. A tank wedged into a low crawlspace takes more care to remove than one standing in a garage, so tell us where yours is when you call.

Booking the tank swap

Let us know what the pump is doing, where the tank sits and, if you can read it, the size printed on its label when you call (336) 613-4314. A phone photo of the tank and gauge helps. If the tank is in a crawlspace, tell us how the access door opens and whether anything is stored in front of it. The office answers weekdays from 8am to 5pm, and on Saturday or Sunday you can call or text.

Coming from Greensboro, we pick up NC 61 to reach homes around town. A tank swap is usually planned work, but if short cycling has already burned out the switch and the water is off, say so and we will handle it as a no-water call.

ZIP code we cover around Gibsonville: 27249.

Questions from Gibsonville

Still stuck? (336) 613-4314

We are on Gibsonville town water. Do we need a pressure tank?

No. Town customers get their pressure from the public system, so there is no well pump to protect and no tank to maintain. A pressure tank belongs with a private well. If you just bought the house and are unsure which you have, check your closing papers or ask the town whether the address has a water account.

Does replacing a pressure tank near Gibsonville need a county permit?

No. North Carolina law exempts repairing or replacing a well pump or tank from the repair permit, as long as the work does not break or open the well seal. That holds on the Guilford side of town and the Alamance side alike, because it is state law, not a county choice.

How far is the well from the house on a typical lot near Gibsonville?

It depends on the lot, but state rules set a minimum. A private well has to sit at least 25 feet from the house, and it must be kept 100 feet from a septic system, a distance a tight single-family lot can reduce to 50. That puts the well out in the yard, with a buried line carrying water to the tank.

Is it worth adding air to a waterlogged tank instead of replacing it?

Sometimes. Old tanks without a bladder were meant to be drained and recharged with air now and then. A modern bladder or diaphragm tank that is waterlogged almost always has a torn bladder, and adding air buys only a few days. We check the tank type and the bladder before recommending a new one.

How big a pressure tank does our house need?

Big enough that the pump gets a real run each cycle instead of quick bursts, and small enough to fit where the old one sat. The right size depends on your pump's output and your switch setting. A larger tank means fewer starts, which is easier on the pump, so we often size up when space allows.

Our tank is in a cramped crawlspace. Can it go somewhere easier to reach?

Often it can. A tank can sit in a garage, utility room or well house as long as it stays above freezing and the line from the well can be rerouted to it. That adds work, so we look at the space first and tell you whether the move is worth it or whether a new tank in the same spot makes more sense.

Why does the pressure drop so fast before the pump kicks on?

That fast drop means the tank has little or no air left. With a good air charge, pressure eases down slowly as the tank empties, and the pump starts at the cut-in setting. Without one, the tank holds almost no usable water, so pressure crashes and the pump jumps on within seconds of opening a tap.

How often should someone look at the tank and switch?

Once a year is a good habit. The National Ground Water Association recommends a yearly checkup by a licensed or certified well professional that covers the pump motor, the pressure tank, the pressure switch, a flow test and a water test for coliform bacteria and nitrates.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.