Pressure Tank Replacement in Reidsville, NC

Click on, click off, every few seconds while the shower runs.

Map: Reidsville, NC in relation to GreensboroReidsvilleGreensboro20.8 miWentworthBrowns SummitEdenStonevilleALAMANCEGUILFORDSTOKESCASWELL
Town
Reidsville, NC
County
Rockingham County
From our Greensboro office
20.8 miles, straight line
Open Reidsville in Google Maps

In a home outside Reidsville's city water system, that rhythm usually means the pressure tank has quit doing its job, with a torn bladder or an air charge that leaked away. Pressure tank replacement in Reidsville stops the short cycling before it wears out your pump and pressure switch.

What the tank does and what we swap out

A pressure tank holds water under a cushion of air, so a short draw at the sink comes out of the tank instead of starting the pump. Inside most modern tanks, a rubber bladder or diaphragm keeps the air and water apart. The air side is pre-charged to about 2 psi below the pressure switch's cut-in point. When that air leaks off or the bladder tears, water fills the whole tank, the cushion is gone, and the pump starts and stops in quick bursts.

Replacement means more than the tank itself. The tank tee, gauge, and relief valve usually share one fitting, and corroded ones get changed along with it. We size the new tank to your pump and household, since a larger drawdown means fewer starts per day. The air charge gets set to match your switch, whether that is 30/50, 40/60, or something else. The switch itself gets a look too, because a tank that has been waterlogged for months has often worn the switch contacts along the way.

A waterlogged tank wears down everything around it

Every pump start draws a surge of current and heats the motor. A tank with no air cushion turns a handful of starts an hour into dozens. The pump pays for that first, then the pressure switch, whose contacts pit and weld from all the arcing.

Inside the house, you notice it too. Pressure jumps around in the shower, pipes can bang as the pump slams on and off, and every valve takes more strain. An old steel tank that has started rusting from the bottom will eventually leak, and if it lives in a crawlspace or a finished basement, that leak can run a long time before anyone sees it.

When pressure tank replacement in Reidsville is the fix

The clearest sign is the sound: the pump clicking on within seconds of opening a tap, and off again just as fast. Watch the gauge on the tank tee if you have one. A healthy tank lets the needle drift down slowly from cut-out to cut-in. A failed one drops it in a heartbeat.

Knocking on the tank tells a story too. Rap it with your knuckles from the top down. A working tank sounds hollow near the top, where the air sits. A waterlogged one sounds dull and solid all the way up.

Other signs come on slowly. Rust spots or weeping seams on the shell. A damp floor under the tank. Pressure that surges and sags in the middle of a shower. And if water spits out of the air valve when we test it, the bladder has torn and the tank is finished.

Changing out a tank, stage by stage

Shutting down and emptying

We turn off power to the pump at the breaker, open a tap to bleed off pressure, and empty the old tank. A waterlogged tank holds a lot of water and weighs far more than its size suggests, so it comes out carefully.

Setting the new tank

The new tank goes on a level, dry spot with room to reach the air valve later. Before any water goes in, we set its air charge 2 psi below the cut-in pressure on your switch.

Fittings and switch

The tank tee, gauge, and relief valve go on, along with a union or shutoff that makes the next service easier. We check the switch contacts and the small sensing tube under the switch, and clean or replace what needs it.

Testing the cycle

With power back on, we watch the gauge through several full cycles, confirm the cut-in and cut-out points, and check every joint for leaks. You should hear the pump run longer and start far less often.

City pressure versus well pressure around Reidsville

Inside the city, water pressure comes from the City of Reidsville's own system. NC DEQ's 2025 water supply plan lists a treatment plant rated at 9 million gallons a day and a year-round population served of 15,000, close to the 14,692 people the Census Bureau estimated for the city that year. NC DEQ also lists the other public systems in Rockingham County: Eden, Madison, Mayodan, Stoneville, and one owned by the county. If your house is not tied into one of those, the pressure at your taps comes from a tank and a switch somewhere on your own property.

That catches people who move out from town. City pressure feels steady because a whole system holds it up. A well system swings by design, climbing to the cut-out setting, then falling to cut-in before the pump restarts. On a 40/60 switch that is a 20 psi swing, and it is normal. A swing that repeats every few seconds is not.

Where the tank sits depends on the house and how the system was first set up. We find them in basements, crawlspaces, garages, utility closets, and pump houses out by the well. Crawlspace tanks are the hardest to reach and the easiest to forget, and they are often the ones that have been waterlogged longest by the time anyone notices. Part of a replacement is asking whether the new tank belongs somewhere easier to get at.

When to call and how we get there

We keep the schedule from 8am to 5pm on weekdays. Weekends, a text or a call to (336) 613-4314 works. Reidsville lies northeast of our Greensboro base, and NC 87 is one of the roads that runs through it. We also look after wells in Browns Summit and Summerfield. A photo of your tank and its label, sent by text, helps us bring the right replacement.

ZIP code we cover around Reidsville: 27320.

Questions from Reidsville

Still stuck? (336) 613-4314

Do I need a permit in Rockingham County to replace a pressure tank?

Not for the tank. A tank swap is above-ground work on the water line, and state law exempts pump and tank replacement from the repair permit that applies to wells themselves. The well seal is never opened. Rockingham County's permit rules come into play for work on the well structure, such as casing, not for a new tank in the basement.

I moved from Reidsville city water to a house with a well. Why does my pressure rise and fall?

Because a well system works inside a range. The pump fills the tank until pressure reaches the cut-out setting, then stops, and you draw the tank down to cut-in before it starts again. On a 30/50 switch, that is the difference between 30 and 50 psi at the tap. A slow drift between the two is normal. A jump every few seconds means the tank needs attention.

Do you replace pressure tanks for homes off NC 87 near Reidsville?

Yes. NC 87 runs right through Reidsville, and homes off it are well within the area we cover. When you call, tell us the street address, where the tank sits in the house, and whether it is an old steel tank or a newer bladder model if you know. That helps us show up with the right tank and fittings.

How many years will a pressure tank hold up?

Nobody can give you a fixed number. Life depends on how hard the tank is cycled, whether it was sized right, what the water does to the fittings, and where the tank lives. A tank in a damp crawlspace rusts faster than one in a dry basement. Short cycling from a bad switch or a leaking check valve wears out a bladder early. We judge each tank by its condition, not its age.

Can I fix a waterlogged tank by adding air?

Sometimes, on an old tank without a bladder, adding air helps for a while, though it will waterlog again. On a bladder or diaphragm tank, air only fixes things if the bladder is still whole and the charge simply leaked down. A shot of water from the air valve means the bladder has failed and the tank has to be replaced.

Is a bigger pressure tank better?

Up to a point. A larger tank gives a longer drawdown, which means fewer pump starts and longer, cooler runs. That is easier on the motor and the switch. The limits are floor space, the weight of the tank full of water, and the pump's output. We size the tank to your pump and to how your household uses water, then set the air charge to match.

What should the air pressure in my tank be set to?

About 2 psi below the cut-in setting on your pressure switch, checked with the tank empty of water. A 30/50 switch calls for 28 psi, and a 40/60 switch calls for 38 psi. Set it too high or too low and the tank holds less usable water than it should, so the pump starts more often. We set and check it on every tank job.

My pressure tank is wet on the outside. Is it leaking?

Often not. Cold well water inside the tank chills the steel shell, and moisture in warm, humid air condenses on it, the same way a glass of ice water sweats. That alone is not a failure, but standing moisture rusts the tank from the outside, especially near the bottom. Flaking paint, rust at the base, or a wet floor beneath it are worth a look before they turn into a leak.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.