Well Pump Replacement in Asheboro, NC

Some pumps are past saving. The motor has burned out, the readings show it going, or it has come up out of the well twice in a few years.

Map: Asheboro, NC in relation to GreensboroAsheboroGreensboro25.2 miRandlemanRamseurArchdaleTrinityDAVIDSONRANDOLPH
Town
Asheboro, NC
County
Randolph County
From our Greensboro office
25.2 miles, straight line
Open Asheboro in Google Maps

At that point, the well pump replacement Asheboro homes need comes down to sizing a new pump to your well and house, and checking the pipe, wire, and splices that come up the hole with the old one.

Sizing a new pump to the well, the wiring, and the house

Replacing a pump starts with what the old one was asked to do. We want to know how fast the well recovers, where the old pump was set, what the pressure switch is set to, and how much water the household uses at once. A pump that is too big for a slow well will empty it. An undersized one never gets the system up to pressure.

Then comes the type. Submersible pumps sit down in the well. Jet pumps sit above ground and pull water up, and they suit shallower wells. A two-wire submersible keeps its starting parts inside the motor, while a three-wire model needs a control box in the house or at the wellhead, and the replacement box must be matched to the replacement motor.

Everything that rides up with the old pump gets a look: drop pipe, wire, splices, check valves, torque arrestor, and the pitless adapter. State rules say a certified well contractor has to be on site for any pump job that breaks the well seal. We are certified as a water well contractor in North Carolina, and our founder has held a trade license since 1974.

What happens while a dying pump hangs on

Slow failures do their damage quietly. Every hard start heats the motor windings a little more. The pump takes longer to reach pressure, and the household gets used to weak showers and a gauge that lags behind. A worn check valve can let water fall back down the pipe every time the pump stops, so each restart begins against an empty column and the motor works harder still.

A motor drawing too much current can also take the control box or the pressure switch down with it, so one failure becomes two. Then it stops for good, on its schedule, not yours. Waiting also narrows the choices. A planned replacement leaves room to talk about pump size, a new tank, or a constant-pressure system. A replacement done with no water in the house usually goes in with whatever fits and is already on the truck.

Readings that say the pump is finished

Some readings point past repair:

  • Amperage far outside the motor's rating, with good voltage at the switch.
  • Insulation readings on the motor and wire that show a short to ground.
  • A pump that runs but cannot build pressure, after the tank and switch check out.
  • Sand or grit in the water from a pump with worn impellers.
  • A motor that was already replaced once and is failing again.
  • A jet pump that keeps losing prime even with a sound foot valve and suction line.

We also judge the wire. Splices that have been redone two or three times, or a jacket nicked from years of rubbing on the casing, usually mean the whole string should come out new along with the pump.

Age alone is not on that list. Plenty of old pumps test fine, and we leave those in the well. What counts is how the pump reads today and what the well can give it.

Swapping the pump, from first reading to written record

No pump gets pulled on a guess.

  1. Fresh readings confirm the diagnosis first.
  2. The breaker gets switched off and locked out, and the well cap comes off.
  3. Pump, pipe, and wire are lifted out as one string, and each length gets inspected as it clears the casing.
  4. You see what failed and anything else we found, and we agree on the replacement before new parts go in.
  5. The new pump is spliced, wired, and lowered on sound pipe and wire, with a matching control box if it needs one.
  6. We restart the system, set the switch, check the tank charge, and watch the pressure through full cycles.
  7. The well is disinfected, as state rules call for after pump installation, and you get plain directions for flushing it and testing the water.
  8. We write down the new pump's model and setting for your records, so the next person who works on the well is not guessing.

Well pump replacement Asheboro properties need, from 1796 to now

Asheboro is older than most people guess. The State Legislature chartered the town on Christmas Day 1796, and it took shape on a 50-acre tract around the courthouse square on Main Street. Growth came with the rails. Rail service arrived in July 1889, a second line followed in 1896, and the population went from 510 in 1890 to 5,021 by 1930. The Census Bureau puts it at 27,990 in 2025.

For pump work, that long history means we assume nothing about the house. A well on an older property can still have a jet pump, galvanized drop pipe, or wire sized for a smaller motor. A newer house may run a three-wire submersible with its control box out in a garage. We find out what is there before we order a single part, because the right pump for one lot can be the wrong pump for the next.

Sometimes the pump is not the real problem. A well that can no longer keep up may need replacing, and that is a permitted job through Randolph County Environmental Health, not a pump swap. We do not put in new wells. We will be plain with you, though, when a new pump would only go down a well that cannot feed it, so you spend your effort on the part that actually failed.

Booking a planned pump replacement down I-73

We set the schedule Monday through Friday, from 8am to 5pm. On Saturday and Sunday, call or text. Reach us at (336) 613-4314, and these jobs bring us south from Greensboro on I-73.

If you have paperwork from the last pump job, such as a receipt or a tag on the control box, keep it handy. The old pump's size and setting save guesswork, and a call made while the pump is still limping gives us time to bring the right one. Describe the symptoms when you call so the truck comes loaded for a replacement rather than a repair.

ZIP codes we cover around Asheboro: 27203, 27205.

Questions from Asheboro

Still stuck? (336) 613-4314

Does replacing a pump in Asheboro need a Randolph County permit?

No. State law exempts pump repair and pump replacement from the repair permit requirement, so there is nothing to file with Randolph County for the pump itself. The well does have to be disinfected afterward, and a certified contractor has to be there for any job that breaks the well seal. A liner or casing extension is different: that needs a Repair Well Permit.

What happens to the old well if a new one goes in on my lot?

Randolph County requires an Abandonment Well Permit to close a well for good. The well contractor schedules the abandonment and submits a Well Abandonment Record (GW-30) once it is done. An old well left open is a straight path from the surface into the groundwater your new well draws on, which is why it has to be sealed properly.

If my well has to be replaced, who chooses where the new one goes?

Under Randolph County's New Well Permit, an Environmental Health Specialist visits the property and sets a location that meets the required setbacks. The county inspects the grout placement and the wellhead, and the well contractor submits a Well Construction Record (GW-1). We do not put in new wells, but we can help you understand your options before you call a contractor who does.

Does a new pump mean a new tank too?

Not always, but it should be checked. A new pump working against a waterlogged tank will short cycle from day one and wear out early. If the tank's bladder has failed or the shell is rusting, replacing both on the same visit saves opening the system twice. If the tank tests fine, it stays.

Is a constant-pressure pump worth considering?

It can be. A variable-speed pump changes its speed to hold pressure steady, so showers do not swing between strong and weak as a standard switch cycles. It needs a matched pump and controller, and it runs with a smaller tank. It is not the right answer for every well, and when a standard pump suits yours better, we say so.

Can I switch from a jet pump to a submersible?

Often, yes, if the well is a drilled well with casing wide enough for a submersible and enough water above the intake. Moving to a submersible gets the pump out of the basement or pump house and usually quiets the house. We check the casing size and the well's recovery before recommending it.

How do you decide what size pump to put in?

We size from the well and the house: how quickly the well recovers, how deep the pump will hang, the pressure switch setting, and how many taps run at once. Testing drawdown and recovery shows what the well can really give. Oversizing a pump on a slow well is one of the most common mistakes in this trade.

Will the water look or smell different after the replacement?

For a short while, yes. The well is disinfected with chlorine after pump installation, so expect a bleach smell until it has been flushed through. Water may also run cloudy or carry a little sediment stirred up when the old pump came out. Once the chlorine is gone, a bacteria test confirms the well is clean.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.