Pressure Tank Replacement in Danville, VA

In an older house the pressure tank sits wherever it fit: a cellar corner, a crawlspace, a shed over the wellhead.

Map: Danville, VA in relation to GreensboroDanvilleGreensboro41.8 miYanceyvilleEdenReidsvilleWentworthALAMANCEGUILFORDSTOKESPITTSYLVANIAHENRY
Town
Danville, VA
County
Independent city bordered by Pittsylvania County
From our Greensboro office
41.8 miles, straight line
Open Danville in Google Maps

When that tank loses its air, the pump clicks on for every glass of water and the shower pressure swings up and down. Pressure tank replacement in Danville gets the tired tank out of its tight spot and a properly charged one in.

Pressure tank replacement in Danville: what gets swapped and set

The tank's job is simple. It stores water under air pressure so the pump doesn't have to start every time someone opens a tap. Inside a modern tank, a rubber bladder or diaphragm keeps the air and the water apart. As water comes in, the air gets squeezed. When you draw water, that squeezed air pushes it back out until pressure falls to the switch's cut-in point and the pump starts again.

Replacement means shutting off the pump's power, draining the system, and taking out the old tank. The new one goes onto a tank tee fitted with a pressure gauge, a drain valve, and, where the setup calls for it, a relief valve. Before any water goes in, we set the air charge to about 2 psi below the cut-in pressure. A tank on a 40/60 switch gets charged to about 38 psi. Skip that step and a brand-new tank behaves like a worn-out one.

Size matters as well. A tank that's too small for the pump lets it start and stop too often. We match the tank's drawdown to the pump's output so each run lasts long enough to keep the motor cool.

What a waterlogged tank does to the pump and the switch

Once the air charge is gone, the tank stops cushioning anything. The pump kicks on the moment you open a tap and shuts off the moment you close it. Few things wear out a well pump faster than that kind of short cycling does. Each start sends a surge of current through the motor and wears the switch contacts, and dozens of extra starts a day add up fast.

The damage spreads from there. Switch contacts pit and stick. Start capacitors in a control box wear out sooner. A motor that had plenty of years left gets used up early. A tank rusting from the bottom has its own way of failing: it can split, and if it sits in a crawlspace or a finished basement, a lot of water ends up where you don't want it, soaking insulation and framing and inviting mold.

The pressure swings are the part you notice first, but they're the least of it.

Clues that your tank has lost its air or its bladder

  • Clicking at the switch every few seconds while a tap runs.
  • A gauge needle that swings fast between cut-in and cut-out instead of sliding slowly down.
  • Pressure that drops hard, then jumps back while you're in the shower.
  • A tank that sounds solid when you knock on it. A healthy tank sounds hollow near the top, where the air sits. Solid from top to bottom means it's full of water.
  • Water at the air valve. If we press the valve on top and water comes out instead of air, the bladder has failed.
  • Rust, sweating, or a puddle underneath. Steel shells rust from the outside in damp places, and from the inside out once the bladder lets go.

The tank change, start to finish

  1. We read the air charge with the system drained and check the valve for water. A tank that only needs air gets air, and the visit ends there.
  2. We look over the pressure switch and the fittings. Contacts burned by months of cycling get replaced while everything is apart.
  3. Power goes off at the breaker and stays off for the whole job. The system is drained.
  4. The old tank comes out. In a tight crawlspace or cellar this can be the hardest part, since a failed tank full of water is heavy.
  5. The new tank and tee go in with a new gauge and drain valve, every joint sealed, and the tank set level and supported.
  6. Air goes in before water does, set to 2 psi under your cut-in pressure.
  7. The pump comes back on. We watch the gauge through several full cycles and confirm cut-in and cut-out match the switch.
  8. Every joint gets checked under pressure before we pack up.

Cellars, crawlspaces, and well houses: where older tanks hide

Danville's housing runs old. In Schoolfield alone, the company town Dan River Mills started in 1903, more than a thousand historic buildings still stand. Older houses weren't laid out around a well tank. The tank went wherever it would fit, and a replacement has to work in whatever spot it was given: a crawlspace corner, a cellar under the kitchen, a closet, a garage wall, or a small well house out by the casing.

Each spot brings its own trouble. Crawlspaces are tight and damp, which is hard on a steel tank shell. Unheated cellars and well houses can drop below freezing in a cold snap, and a frozen tank tee or switch tube shuts the whole system down. Where a well house holds the casing, the tank, and the switch together, Virginia's rules take that into account: the casing must rise at least 12 inches above a concrete floor with a gravity drain, instead of 12 inches above the ground. That drain earns its keep the day an old tank rusts through.

VDH counts more than one million Virginia households on private wells, and every one of those wells pushes water into some kind of pressure tank. The National Ground Water Association recommends a yearly checkup by a well professional that includes the tank and the pressure switch. A simple air-charge reading once a year catches a failing tank before it takes the pump down with it.

Getting a tank change on the calendar

We're based in Greensboro and come north to homes off US 58 on either side of the city, along with anywhere else in town or on the Pittsylvania County land around it where a house runs on a well. Call (336) 613-4314 between 8am and 5pm on a weekday, or call or text on a Saturday or Sunday.

We book the visit. Tell us where the tank sits and how tight the space is. If you can, text a photo of the tank, its gauge, and the label on its side. The label tells us the size and often the age, so we can bring a tank that fits.

ZIP codes we cover around Danville: 24540, 24541.

Questions from Danville

Still stuck? (336) 613-4314

My tank is in a tight crawlspace under an older Danville house. Can it be moved somewhere easier to reach?

Sometimes. A tank can go in a different spot if the piping between the well line and the house allows it and the new location stays above freezing. Moving it can make every future service call easier. We look at the layout during the visit and tell you plainly whether a move makes sense or the new tank should go back where the old one was.

Do you replace tanks in well houses out in Pittsylvania County?

Yes. A well house is one of the most common places for a tank, and it brings its own checks: whether the space stays above freezing, whether the floor drains, and whether the casing stands high enough above that floor. We look at all three while we're there, since a frozen or flooded well house can take out a new tank.

My older Danville home has a big gray steel tank with no air valve. Is that a problem?

That's probably a galvanized tank without a bladder. It keeps a cushion of air above the water, and the air slowly dissolves, so these tanks waterlog and need regular draining or an air-volume control to keep working. Most get replaced with a bladder tank, which holds its charge far longer and takes up less room.

Can a tank be recharged instead of replaced?

If the bladder is intact and the air charge has just leaked down over time, yes. We drain the system, set the charge to 2 psi below cut-in, and watch it cycle. If the air valve spits water, the bladder is torn and a recharge won't hold. That tank needs replacing.

What decides the right tank size for my pump?

It depends on the pump's flow and your switch settings. The goal is a drawdown big enough that the pump runs long enough each time to keep the motor cool. A bigger tank isn't always better if it won't fit the space, so we size it to the pump and to the spot it has to go in.

What pressure should my tank be set to?

About 2 psi below the pressure switch's cut-in point, measured with the tank empty of water. On a 20/40 switch that's around 18 psi. On a 30/50 switch, about 28 psi. A tank charged wrong will make even a healthy pump short cycle, so this is the first thing we check on any tank call.

Will a bad tank wear out my well pump?

It can, given time. Short cycling puts far more starts on the motor than it was built for, and each start brings a jolt of current and heat. The switch and the control box parts wear out too. Catching a failing tank early is about the easiest way to spare the pump hanging down in your well.

Is it safe to check my own tank?

Yes, within limits. Watching the gauge through a cycle is safe, and so is tapping the tank to hear where the water line sits. Leave the pressure switch cover on, since there's line voltage under it, and leave draining and recharging to us, since that work happens right beside the pump circuit. A photo of the gauge and the tank label tells us a lot.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.