Emergency No-Water Service in Martinsville, VA

Nothing at the kitchen tap, the gauge on zero, and no city line to fall back on. That is the morning behind most emergency well service Martinsville families ask for.

Map: Martinsville, VA in relation to GreensboroMartinsvilleGreensboro43.0 miRidgewayEdenStonevilleALAMANCEPATRICKSTOKESFRANKLINCASWELLPITTSYLVANIAHENRY
Town
Martinsville, VA
County
Independent city surrounded by Henry County
From our Greensboro office
43.0 miles, straight line
Open Martinsville in Google Maps

On a house out in Henry County, it usually traces to one failed part rather than a dry well, and a few checks before you call can tell us a lot.

Emergency well service in Martinsville: getting the water back on

An emergency no-water call is a repair with the clock running. The goal is to find out why the water stopped, get it flowing again, and then sort out whether the fix is permanent or needs a follow-up visit.

The causes fall into a few groups. Power problems come first: a tripped breaker, a failed pressure switch, a dead capacitor or relay in the control box, or a damaged wire between the house and the well. Then the pump itself, which may have a burned motor or a split drop pipe. Then the water: a well pumped below the intake, or a line that has frozen or broken between the well and the house. Each one looks the same from the kitchen sink, which is why we test instead of guessing.

Some of those causes can be set right on the first visit and some cannot. A tripped breaker or a burned switch usually can. A pump that has failed down the hole has to be pulled and replaced, and the well disinfected afterward.

We hold Virginia water well license 2719001436, and the state requires a license and certification for anyone who repairs a private well. That matters on an emergency call, because getting water back sometimes means opening the well.

Why a dead well should not wait for a convenient week

No flushing, no cooking, no washing up. In winter there is also no water moving through pipes that may already be close to freezing, and lines that freeze solid can split, so a no-water problem becomes a leak the moment the water comes back.

The temptation is to keep resetting the breaker and hope. Each forced restart on a shorted motor or failing control box adds damage, and a pump that runs with no water around it can burn itself up. Hauling water from a creek or pond for drinking or cooking brings its own risk, since that water has had no treatment and no testing.

Waiting also hides the evidence. A switch that welded shut or a control box that scorched during a storm tells us a lot while the clues are fresh. After days of resets and guesswork, the original fault is harder to read, and something else may have failed in the meantime.

Telling a real emergency from a weekday problem

Not every pressure problem needs the first opening on the schedule. Here is how we sort them.

Call right away

  • No water at any tap, and the gauge reads zero.
  • The pump breaker trips again after one reset.
  • The pump runs nonstop while pressure stays low, which can mean a broken pipe between the well and the house.
  • A wet, soft patch in the yard along the line from the well.
  • Floodwater has covered the wellhead.

Can usually wait for a weekday

  • Pressure is lower than normal but steady.
  • The switch clicks more often than it used to, but water still comes.
  • Water runs cloudy or off-color for a day after heavy rain while pressure stays normal. Drink bottled water until it has been tested.

What we do when we reach a house with no water

  1. The gauge and breaker come first, because sometimes the answer is right there.
  2. Next is power: voltage at the pressure switch and the control box, then the capacitor and relay.
  3. Electrical readings on the pump circuit tell us whether the motor and the wire down the well are sound.
  4. If the pump runs but no water arrives, we look for a broken pipe, a failed check valve, or a well drawn below the intake.
  5. We fix what failed. If the lasting fix needs a part we do not have on hand, you will know before we leave, along with what comes next.
  6. Once water is back, we bleed air from the lines, watch the pump through several cycles, and disinfect the well if it was opened.

Where floodwater reached the wellhead, Virginia Cooperative Extension recommends shock chlorination, and we would add a bacteria test before anyone drinks the water again.

Roads into Martinsville and what to do before we get there

US 220 is our road in. It runs south from the city through Ridgeway toward Greensboro, so we come up it from the south. US 220 and US 58 share a bypass along the south side of the city, and that is how we reach houses east or west of town along US 58. Out on the county roads, the name of the nearest crossroad helps us more than a mailing address.

Before we arrive

  • Look at the pump breaker. If it has tripped, you can reset it one time. Should it trip again, leave it alone until we get there.
  • Keep the pressure switch and control box shut, and no tapping on them to coax the pump along. Both carry line voltage.
  • Turn off any treatment equipment that backwashes on a timer, such as a softener or filter, so it does not try to run dry.
  • Set aside bottled water for drinking, and fill a bucket for flushing if a neighbor can spare water.
  • In cold weather, check whether an exposed pipe or the well house may have frozen, and tell us.
  • If the wellhead is under water, leave the pump off until the water goes down.
  • Clear a path to the well and the tank, and put dogs inside so we can get straight to work.

Calling for help when the water is out

During the week, 8am to 5pm, we answer (336) 613-4314 and book the visit. Weekend calls and texts go to the same number. Give us the address, what you have checked, and what you are hearing from the pump.

We come from Greensboro, to the south. If anyone in the house depends on water for medical reasons, or the wellhead flooded, say so when you call.

ZIP code we cover around Martinsville: 24112.

Questions from Martinsville

Still stuck? (336) 613-4314

Which Martinsville ZIP codes do you answer no-water calls in?

All of them: 24112, 24113, 24114, and 24115. The last three are PO box ZIPs, so for a service call what matters is where the house and well actually sit, inside the city or out in Henry County. Give us the street address, and we can find you.

Do you also cover Ridgeway and the North Carolina towns near Martinsville?

Yes. Ridgeway, on US 220 south of the city, is on our list, and so are Eden, Stoneville, Mayodan, and Wentworth on the North Carolina side. A no-water call in any of them gets the same approach: test first, fix the part that failed, and disinfect the well if it had to be opened.

How far is Martinsville from your Greensboro base?

About 43.0 miles north of Greensboro as the crow flies. Both the city and the rural roads outside it are regular stops for us in Virginia, as Danville is, so a no-water call there is routine work. We will tell you where you fall on the schedule when you call.

Is my water safe to drink once it comes back on?

If nothing opened the well, the water is usually the same as it was before the outage. If the pump was pulled or the wellhead flooded, use bottled water until the well is disinfected, flushed, and tested for bacteria. Virginia Cooperative Extension recommends shock chlorination after maintenance or repair work on a well and after any flooding.

Could my well have simply run dry?

It can happen, though a failed part is the more common cause. A well can be pumped down faster than it refills, especially in a dry stretch or after heavy use, such as hours of watering a garden. The water usually comes back as the well recovers. Running the pump in that state can damage it, so we check the well and the pump both.

What should I tell you when I call about having no water?

Your address, when the water stopped, and what you have already checked. Tell us whether the pump is silent, humming, or running without stopping, what the pressure gauge reads, and whether there was a storm, a power outage, or freezing weather. Those details help us bring the right parts and test the likely cause first.

Can frozen pipes cause a no-water call?

Yes. A pipe that freezes between the tank and the house, or an exposed line in a well house or crawlspace, stops water just like a failed pump. The pump may run against the blockage or shut off on high pressure. Never use an open flame to thaw anything. Tell us the trouble came with the cold, and we will check the lines first.

The pump is humming but the taps are dry. What is going on?

A hum with no water often points to a stuck pump, a failed start capacitor, or a motor trying to start on low voltage. It can also mean the pump is running but a broken pipe or failed check valve keeps water from reaching the house. Switch the breaker off so the motor does not overheat, and call us.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.