Well Pump Repair in Martinsville, VA

Out past the end of the city water mains, most of the well pump repair Martinsville homeowners call about starts with one of three complaints: no water, pressure that surges and sags, or a pump that will not shut off.

Map: Martinsville, VA in relation to GreensboroMartinsvilleGreensboro43.0 miRidgewayEdenStonevilleALAMANCEPATRICKSTOKESFRANKLINCASWELLPITTSYLVANIAHENRY
Town
Martinsville, VA
County
Independent city surrounded by Henry County
From our Greensboro office
43.0 miles, straight line
Open Martinsville in Google Maps

Usually one part has failed, not the whole system. We find which part, fix it, and leave the good ones alone.

Well pump repair in Martinsville usually starts above ground

A private well system has a short list of working parts, and most of them are not down the hole. The pressure switch near the tank starts the pump on low pressure and stops it on high. A three-wire submersible also has a control box on the wall that holds the start capacitor and relay. Add the breaker, the buried wire out to the wellhead, and the pitless adapter below the frost line, and only then do you reach the pump and motor hanging in the casing.

Repair means testing those parts in order and fixing the one that quit. A burned switch contact, a dead capacitor, or a corroded splice will stop water just as completely as a seized motor, and none of them requires pulling anything out of the well. When the trouble really is below ground, the pump comes up so we can look at the motor, the drop wire, and the check valve. If it is past saving, you will hear that from us plainly.

In the stretches of Henry County where no public water line runs past the house, the well is the only supply. That is why we test before we replace anything. A guessed part that turns out to be wrong leaves you without water for another day.

What a pump that half works does to the rest of the system

A pump that limps along rarely stays that way. Pitted switch contacts chatter and arc until they weld shut, and then the motor runs with nothing to stop it. A motor that keeps tripping its thermal overload cooks its windings a little more every time. Short cycling, with the pump starting and quitting every few seconds, wears out start parts and motors far sooner than normal use would.

Then there is the water level. If the pump keeps running after the level in the well falls below its intake, it can burn up quickly, since moving water is what cools the motor. A problem that started as a small relay or switch ends as a full pump replacement, with the well opened and disinfected afterward.

How a failing pump tells on itself

Pumps rarely quit without some warning first. Watch and listen for these:

  • Pressure that fades in the middle of a shower and then recovers.
  • Clicking at the pressure switch with no water moving.
  • A pump breaker that trips, gets reset, and trips again.
  • Air spurting from the faucets, or water that runs cloudy right after the pump starts.
  • A pump that keeps running long after everyone has turned the water off.
  • An electric bill that climbs for no reason you can find.

One more belongs on the list: everything worked before a thunderstorm and nothing works after it. Lightning and power surges are among the most common reasons a control box or pump motor fails, so tell us if the trouble started with a storm.

Our order of testing on a pump repair call

We work through the system in the same order every time, so nothing gets skipped.

  1. We ask what you noticed and when. "It quit during the storm" points one way. "It has been getting weaker for weeks" points another.
  2. We read the pressure gauge and watch the switch through a full cycle, if the pump will run at all.
  3. We check the breaker and measure voltage at the switch and, on a three-wire system, at the control box.
  4. We test the capacitor and relay, then take amp draw and resistance readings on the motor leads. Those numbers show whether the fault is in the motor, the wire, or a splice.
  5. We check the tank's air charge, since a waterlogged tank can pass for a bad switch.
  6. If the fault is down the hole, we pull the pump, inspect the splices and check valve, and either repair it or talk with you about replacement.
  7. When the pump has come out, the well is disinfected before it goes back into use.

Before we leave, you get a plain account of what failed, why it failed, and what to keep an eye on.

Why homes around Martinsville still depend on their pumps

Out in Henry County, public water is the exception rather than the rule. Outside the Henry County Public Service Authority's lines, the water usually comes from a private well with a pump in it.

The Public Service Authority has been working at that gap. In March 2023 it sampled water in the Iriswood, Horsepasture, and Ridgeway districts for a Virginia Department of Health funding application, with the aim of running lines into underserved communities that rely on wells. Until a line actually reaches your road, though, your pump is your water supply, and it has to keep working.

The rock under the county matters too. The U.S. Geological Survey describes the Piedmont as dense bedrock that gives up water mainly through fractures, beneath a layer of weathered rock and soil. A well fed by a few fractures may refill slowly. When a pump outruns that recovery, it can draw the water down to its intake, which is why we check how a well around Martinsville recovers before we blame the pump.

Calling us and getting us up US 220

Call (336) 613-4314. We answer weekdays from 8am to 5pm and put you on the schedule. On Saturday and Sunday, call or text the same number and describe what the pump is doing.

We are based in Greensboro and come north on US 220 to reach the city and the county roads around it. When you call, tell us whether the house is in the city or the county and where the well and tank sit, so the right parts are on the truck.

ZIP code we cover around Martinsville: 24112.

Questions from Martinsville

Still stuck? (336) 613-4314

Will you come up from Greensboro to repair a single pump in Martinsville?

Yes. Measured in a straight line, Martinsville sits 43.0 miles to our north, and it is part of our regular Virginia service area along with Danville. One failed switch or control box is a normal service call for us, and a house on a well has no other supply while the pump is down.

Public water might reach my Henry County road someday. Is it worth fixing my pump now?

If the pump is your only supply today, yes. The Public Service Authority has studied and extended lines into communities that rely on wells, but a study is not a pipe in the ground. Most pump repairs come down to one part, such as a switch, capacitor, or splice, and they keep you in water until a connection is real.

Does Virginia have rules about who works on the pump in my well?

Yes. Virginia requires anyone who builds, repairs, or alters a private well to be licensed and certified through the Department of Professional and Occupational Regulation. The state also requires the well to be disinfected after any work that reaches inside the casing, and pulling a pump counts. Fixing a switch or control box, which sit outside the well, does not open it.

Can a burned-out pressure switch be replaced without pulling the pump?

Usually. The switch is a separate part mounted near the tank, and when its contacts burn or the small tube under it clogs with sediment, the switch alone gets replaced. We check the tank's air charge at the same time, because a waterlogged tank can make a good switch look bad and will wear out a new one.

How do I tell a failing pump from a waterlogged tank?

From inside the house, they can feel alike. With its air charge leaked away, a tank lets the pump run in short bursts, a few seconds on and a few off. A weak pump does the opposite: it runs a long time and never builds full pressure. Gauge readings during a cycle and a precharge check with the system drained tell the two apart.

My pump breaker tripped again right after I reset it. What now?

Leave it off this time. One reset is reasonable after a storm, but a breaker that trips twice is reporting a real fault, often a shorted motor, damaged wire, or failed control box. Forcing it back on can turn a repairable problem into a burned-out pump. Do not open the switch or control box yourself.

Once a pump has been pulled, does it always get replaced?

No. Pulling the pump lets us look at the splices, the wire, the check valve, and the pump itself. A bad splice or a failed check valve can be fixed and the same pump set back down. A new pump makes sense only when the motor itself has failed or the pump is too worn to supply the house.

Is a water test worth doing after a pump repair?

Yes, whenever the well was opened. The EPA recommends testing right away after you repair or replace any part of a well system. A coliform bacteria test, taken after the well has been disinfected and the chlorine flushed out, shows whether anything got in while the casing was open.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.