Pressure Tank Replacement in Martinsville, VA

Homes on city water in Martinsville get their pressure from the city system. Move out to a house on a well in Henry County, and a pressure tank does that job instead.

Map: Martinsville, VA in relation to GreensboroMartinsvilleGreensboro43.0 miRidgewayEdenStonevilleALAMANCEPATRICKSTOKESFRANKLINCASWELLPITTSYLVANIAHENRY
Town
Martinsville, VA
County
Independent city surrounded by Henry County
From our Greensboro office
43.0 miles, straight line
Open Martinsville in Google Maps

When it waterlogs or rusts through, the pump clicks on every time a faucet opens, and pressure tank replacement Martinsville homeowners put off tends to take a pump down with it.

Pressure tank replacement in Martinsville, part by part

Modern pressure tanks hold a bladder or diaphragm with air on one side and water on the other. When the pump runs, water squeezes the air. When you open a faucet, the air pushes water back out, and the pump stays off until pressure falls to the switch's cut-in setting. That stored drawdown is what lets the pump rest between runs instead of starting every time someone rinses a cup.

Replacing the tank means shutting off the pump, draining the system, and disconnecting the old tank from its tank tee. The new tank is sized to the pump and the household, then precharged to about 2 psi below cut-in, so 18 psi on a 20/40 switch. We usually renew the tee, gauge, and relief valve at the same time, since they are already apart and often as old as the tank. An older galvanized tank with no bladder can be swapped for a bladder model, which ends the chore of draining it to restore the air.

What a dead tank does to the pump and the floor

With no air cushion left, a waterlogged tank makes the pump start, build pressure in seconds, shut off, and start again the moment water moves. Every start warms the motor, pits the switch contacts a little more, and, on a three-wire pump, wears the start parts in the control box. Run that way long enough, and a tank problem becomes a pump problem, sometimes with a welded switch on top of it.

Steel tanks also rust from the bottom. A pinhole leak can go unnoticed in a crawlspace or well house until there is standing water, rotted subflooring, or a pump running nonstop to feed the leak. And with no stored water to draw on, pressure at the tap swings hard every time the pump cycles.

Clues that your tank has lost its air

Listen at the pressure switch first. A quick on-off rhythm of clicks whenever water runs is the classic sign. Watch the gauge while someone opens a faucet, and you may see the needle drop and jump over and over instead of falling slowly. Water that spurts or pulses at the tap is the same problem felt from the other end.

The tank gives clues too. A bladder tank should sound hollow when you knock on its upper half. If it sounds solid all the way up, it is full of water. Rust at the bottom seam, a damp spot underneath, or water spitting from the air valve on top all point to a tank on its way out.

None of these mean the pump is bad. They mean the pump is being worked too hard, and the tank is the usual reason.

How we handle the tank swap at your house

First we confirm the tank is really the problem. With the pump off and the system drained to zero, we check the precharge at the air valve. A reading far below where it should be, or water at the valve, settles it. We look at the switch too, because burned contacts often come along with a tank that has been short cycling for months.

Next comes sizing and placement. A larger drawdown means fewer pump starts, but the tank has to fit the space it lives in, whether that is a basement corner, a crawlspace, a garage, or a well house. We set the new tank level on a stable base, connect it, and set the precharge before any water goes in.

Last, we bring the pump back on and watch several full cycles. The gauge should climb steadily to cut-out, the pump should stop cleanly, and the drawdown should match the tank. The National Ground Water Association lists the pressure tank and switch among the items a yearly well checkup should cover, so both are worth a look again down the road.

City water, county wells, and the Martinsville address in between

Martinsville is an independent city. Henry County surrounds it, but the city is not part of the county, and the Census Bureau counts them separately: an estimated 13,849 people in the city and 49,242 in the county as of July 1, 2025.

That split shows up at the tap. The city's Water Resources Department supplies city water, and its 2023 water quality report names the Beaver Creek Reservoir as the main raw water source, with supplemental water drawn as needed from a pump station on Leatherwood Creek. A house on that system gets its pressure from the city. A house on a private well makes its own, with a pump, a switch, and a tank.

Mailing addresses do not always tell you which one you have. The city's standard ZIP, 24112, also takes in Henry County addresses, while 24113, 24114, and 24115 are PO box ZIPs. An address with the city's name on it can belong to a county house on a well. If you bought one recently, the tank in the basement, garage, or crawlspace is now yours to look after, and it is worth learning what a healthy one sounds like.

Getting a tank replacement on the calendar

We run the calendar during weekday hours, 8am to 5pm. On weekends, the phone still takes calls and texts. Reach us at (336) 613-4314.

We come up from Greensboro, heading north into Virginia. A phone photo of your tank, the label on its side, and the pressure switch helps us bring a replacement that fits both the space and the pump.

ZIP code we cover around Martinsville: 24112.

Questions from Martinsville

Still stuck? (336) 613-4314

I moved from Martinsville city water to a house on a well. What does the tank need from me?

Not much, but some attention. Glance at the pressure gauge now and then so you know its normal range, listen for rapid clicking at the switch, and look under the tank for rust or damp spots. A yearly well checkup should include the tank's air charge. City water never asked any of this of you, so it is easy to forget.

My address is Martinsville 24112. How do I know if I am on a well?

The ZIP will not settle it, because 24112 reaches into Henry County as well as the city. Your equipment will. A pump breaker, a pressure switch, and a pressure tank mean you are on a private well. A water bill from a public utility means you are on public water, and the tank question does not apply to you.

Do I need a permit to swap a pressure tank in Martinsville or Henry County?

The tank sits outside the well, usually in the house or a well house. Virginia's private well permit rule is written around constructing, altering, deepening, or abandoning the well itself, and swapping a tank does not touch the casing or the well seal. If a tank job turns up a problem at the wellhead, we will explain what fixing it involves before anything else happens.

What size pressure tank does my well system need?

That depends on the pump's flow, the switch settings, and how the house uses water. The number that matters is drawdown, the amount of water the tank delivers between pump starts, not the size printed on the shell. More drawdown gives the pump longer rests. We size the tank so each pump run lasts long enough to keep the motor healthy.

Can I just add air to my old tank instead of replacing it?

On an old galvanized tank with no bladder, restoring the air is normal upkeep. On a bladder or diaphragm tank, losing air usually means the bladder or the air valve has failed, and adding air only buys a short break before it waterlogs again. Water coming out of the air valve means the bladder is torn and the tank needs replacing.

What air pressure should a well tank be set to?

About 2 psi below the pressure switch's cut-in setting, checked with the pump off and the water drained out of the tank. That works out to 28 psi on a 30/50 switch and 38 psi on a 40/60 switch. A reading taken with water still in the tank is false, which is why quick checks at the valve often miss the real number.

Where should a new tank go if the old one sits in a crawlspace?

Usually in the same spot, since the pipes already run there, as long as it stays dry, does not freeze, and can sit level. If the crawlspace is tight or wet, a new tank sometimes fits better in a garage, basement, or well house nearby. We talk through the choices with you before we move anything.

Why does my well pump click on and off so fast?

Rapid cycling almost always comes back to the tank. When the bladder fails or the air charge leaks away, the tank holds almost no water in reserve, so the pump starts every time a faucet opens. A clogged pressure switch tube can cause similar behavior. Either way, it needs attention soon, because every extra start wears the motor.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.