Well Pump Replacement in Martinsville, VA

Some pumps are worth fixing and some are finished.

Map: Martinsville, VA in relation to GreensboroMartinsvilleGreensboro43.0 miRidgewayEdenStonevilleALAMANCEPATRICKSTOKESFRANKLINCASWELLPITTSYLVANIAHENRY
Town
Martinsville, VA
County
Independent city surrounded by Henry County
From our Greensboro office
43.0 miles, straight line
Open Martinsville in Google Maps

Once a submersible motor tests bad or the pump can no longer keep up with the house, the well pump replacement Martinsville families face comes down to a few real choices: the right size for the well, which wire and fittings to renew, and how long you expect to stay on a well.

Well pump replacement in Martinsville, from pulling to pressure

Inside the casing, a submersible pump hangs on a drop pipe, with the motor at the bottom and the wire running back up to the house. Replacing it means lifting all of that out of the well, setting a new pump and motor on the pipe, and lowering the assembly back to the right depth. A jet pump sits above ground in a basement, crawlspace, or well house instead, but the sizing questions are the same.

Sizing is where the job is won or lost. The pump has to match where the water sits in the well, how quickly the well recovers, and how much water the household uses. Too big, and it can pull a slow well down to its intake. Too small, and the shower fades whenever the washer fills. We also choose between a two-wire motor and a three-wire motor with a control box, usually matching what the house already has.

While the pump is out, the parts that rode down the hole with it get a hard look: the drop pipe, the wire and its splices, the check valve, and the seal at the pitless adapter. Anything tired gets replaced now, not after the new pump is already down there.

Living with a worn-out pump and where it leads

End-of-life pumps seldom quit cleanly. Worn impellers move less water, so the motor runs longer for every gallon and gets hotter doing it. Pressure may never quite reach the cut-out setting, which leaves the pump running without a break. A worn pump can also start pushing grit into the house lines, where it scores valves and clogs any filter or softener downstream.

The bigger problem is timing. A pump that is failing slowly picks its own day to stop, and it is rarely a good one: a cold snap, a holiday weekend, or a house full of guests. Replacing it on your schedule beats replacing it on its schedule.

When a new pump makes more sense than another repair

A few findings point toward replacement instead of repair. The clearest is a motor that tests bad: resistance between the leads that shows a shorted or open winding, or a reading from a lead to ground that shows the insulation has broken down. A motor in that shape cannot be fixed in the field.

Performance tells the rest. If pressure climbs slowly and stalls short of cut-out, if the pump runs for long stretches to refill a tank that is holding its air charge, or if sand shows up in the water when it never did before, the pump itself is likely worn. Repeated failures count too. A pump that needed a new control box, then a new switch, then another repair after the next storm is telling you something.

Age alone is not a reason to replace a pump that tests well. We would rather leave a healthy old pump in a Henry County well than sell you one you do not need.

How a pump replacement goes at your well

Before anything comes out

We confirm the diagnosis first with voltage, amperage, and resistance readings, so nobody pulls a pump that only needed a capacitor. We also note the pressure switch settings and the tank's precharge, since the new pump has to work with both.

Pulling and setting

With the power off at the breaker, we open the well and lift the pump, pipe, and wire out together. The old pump's depth gets checked against the well, and every fitting gets a look. The new pump goes on with a fresh check valve, a waterproof splice kit, and a torque arrestor to keep it centered when it starts. Then the assembly goes back down and seats in the pitless adapter.

Before the water goes back on

Setting a pump means opening the well, and Virginia requires disinfection after that kind of work, so the well is chlorinated and then flushed. We set the switch, match the tank precharge, and run the system through several cycles while watching amp draw and pressure.

Public water lines in Henry County and the pump you pick

A new pump is a long-term purchase, so it helps to know where public water is headed before you choose one. In the county, the Henry County Public Service Authority serves many residents, businesses, industries, and schools through more than 800 miles of utility lines. Its primary source is Philpott Lake, by way of the Smith River, and in 2024 the authority bought 50-year water storage rights from the U.S. Army Corps of Engineers, which operates Philpott Dam.

Those lines keep growing. In October 2026 the authority began a Fairmont Drive extension of about 2,900 linear feet to bring public water to more residents in the Bassett area, after people there raised concerns about their well water earlier in the year. Projects like that go one road at a time.

For your pump, this mostly decides how far to go. If no line is planned for your road, you are buying for the long haul: size the pump carefully, renew the wire and check valve, and set the system up to last. If a connection really is on the way, a dead pump still has to be replaced, because the house needs water now, but we will talk through what is worth doing beyond the pump itself.

Setting up a pump replacement with our office

Office hours run Monday to Friday, 8am to 5pm, and we keep the schedule. On a Saturday or Sunday, call or text and leave the details. The number is (336) 613-4314.

We drive up from Greensboro, south of you across the state line. Our founder has been a licensed tradesman since 1974. If you have the old pump's model plate, a photo of the tank and switch, or paperwork from the last well service, send it ahead. It helps us bring the right pump on the first trip.

ZIP code we cover around Martinsville: 24112.

Questions from Martinsville

Still stuck? (336) 613-4314

Is a permit needed to replace my well pump in Henry County or Martinsville?

Not for the pump itself. Under the Virginia rule that took effect November 6, 2024, a written permit is needed to construct, alter, deepen, or abandon a private well, and the rule says replacing a well pump is not an alteration. If the job turned into deepening the well or changing how it is built, that would be a different matter.

A water line may be coming down my road. Should I hold off on a new pump?

Not if the old pump is dead. The house needs water now, and line extensions in Henry County happen one project at a time. If work on your road is actually scheduled, tell us, and we will keep the replacement to what gets you through. If nothing is scheduled, plan as if the well is staying.

How do I find out whether the Public Service Authority plans a line near me?

Ask the Henry County Public Service Authority directly. It runs the county's public water lines, and its offices are in the Henry County Administration Building at 3300 Kings Mountain Road. A neighbor's word that a line is coming is worth confirming there before you plan around it. We will replace your pump either way.

Is it worth switching from a jet pump to a submersible?

Sometimes. A jet pump sits above ground and pulls water up, which works on shallow wells and some older setups. A drilled well with the water far below the surface is usually better served by a submersible, which pushes water up from inside the casing. If your jet pump has done its job for years, matching it may be the simpler choice.

Does the pressure tank get replaced along with the pump?

Only if it needs it. We check the tank's precharge and bladder whenever we set a new pump, because a failing tank will short cycle the new pump and shorten its life. A tank that holds its air and shows no rust can stay. A waterlogged or leaking one is better replaced now, while the system is already apart.

Can the old pump wire stay in the well with a new pump?

If it tests clean and the insulation is sound, yes. Wire that has been nicked, chafed against the casing, or spliced more than once is a weak spot, and pulling a pump twice means two outages instead of one. We test it with the pump out and tell you what we find.

Why does my water smell like chlorine after a new pump?

Because the well was disinfected. Opening the casing to set a pump can let bacteria in, so the well is chlorinated and then flushed before you use the water. A light chlorine smell can linger in the lines for a short while. If it does not fade once the system has been flushed, call us.

How do you decide what size pump my well gets?

By looking at the well and the household together. We check where the water sits in the well, how it recovers when pumped, how many people live in the house, and anything else that draws water, such as livestock or a big garden. A pump too large for a slow well can pump it down, so bigger is not automatically better.

Good references

Official pages we point homeowners to. They open in a new tab.

No water, low pressure or bad taste?

Call or text. Monday to Friday, 8am to 5pm. Saturday and Sunday: call or text.